manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

Share
Download
D-Link DES-3326SRM Command Line Interface Reference Manual Download Page 134

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

134

 

Spanning Tree Commands 

 

 
DES-3326SR:4# 

 

 

 

 

 

 

 

show stp ports 

Purpose 

Used to display the switch

’

s current per-port 

group STP configuration. 

Syntax 

show stp ports <portlist> 

Description 

This command displays the switch

’

s current 

per-port group STP configuration. 

Parameters 

<portlist> 

−

 Specifies a range of ports to be 

configured. The port list is specified by 
listing the lowest switch number and the 
beginning port number on that switch, 
separated by a colon. Then highest switch 
number, and the highest port number of the 
range (also separeted by a colon) are 
specified. The beginning and end of the port 
list range are seperated by a dash. For 
example, 1:3 would specify switch number 
1, port 3. 2:4 specifies switch number 2, 

1:3-2:4 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands