manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

Share
Download
D-Link DES-3326SRM Command Line Interface Reference Manual Download Page 332

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

332

 

OSPF Configuration Commands 

 

show ospf ipif 

Purpose 

Used  to  display  the  current  OSPF  interface 
settings for the specified interface name. 

Syntax 

show ospf ipif {<ipif_name>} 

Description 

This command will display the current OSPF 
interface  settings  for  the  specified  interface 
name. 

Parameters 

<ipif_name> 

−

  The  IP  interface  name  for 

which you want to display the current OSPF 
interface settings. 

Restrictions 

none. 

Usage Example 

 

To  display  the  current  OSPF  interface  settings,  for  a 

specific OSPF interface: 

DES-3326SR:4#show ospf ipif2 
Command: show ospf ipif2 
 
Interface Name:  ipif2                         IP Address:  123.234.12.34/24 

((Link Up) 

Network Medium Type: BROADCAST    Metric:  1 
Area ID:  1.0.0.0                                   Administrative State:  Enabled 
Priority:  1                                            DR State:  DR 
DR Address:  123.234.12.34               Backup DR Address:  None 
Hello Interval:  10                                Dead Interval:  40 
Transmit Delay:  1                               Retransmit Time:  5 
Authentication:  None 
 
Total Entries: 1 
 
DES-3326SR:4#  

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands