manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

Share
Download
D-Link DES-3326SRM Command Line Interface Reference Manual Download Page 246

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

246

 

IGMP Snooping Commands 

 

config router_ports 

the  highest  port  number  in  a  group, 
separated  by  a  dash.    So,  a  port  group 
including the switch ports 1, 2, and 3 would 
be  entered  as  1-3.    Ports  that  are  not 
contained  within  a  group  are  specified  by 
entering  their  port  number,  separated  by  a 
comma.  So, the port group 1-3 and port 26 
would  be  entered  as  1-3,  26.    Additional 
ports  can  be  individually  entered  by  their 
port number, separated by commas. 

Restrictions 

Only administrator-level users can issue this 
command. 

 

Example Usage: 

To set up static router ports: 
 

DES-3326SR:4#config router_ports default add 2:1-2:10 
Command: config router_ports default add 2:1-2:10 
 
 Success. 
 
DES-3326SR:4# 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands