manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

264

 

DNS Relay Commands 

 

config dnsr [add/delete] static 

Purpose 

Used to add or delete a static entry into the 
switch

’

s DNS resolution table. 

Syntax 

config dnsr [add/delete] static 
<domain_name> <ipaddr> 

Description 

This  command  allows  you  to  add  or  delete 
entries into the switch

’

s DNS cache. 

Parameters 

<domain_name> 

−

  The  domain  name  of  the 

entry. 

<ipaddr> 

−

 The IP address of the entry. 

Restrictions 

Only  administrator-level  users  can  issue 
this command. 

 

Example Usage: 

To add an entry domain name dns1, IPaddress 10.43.21.12 to 
DNS static table. 

 

 

 

DES-3326SR:4#config dnsr add static dns1 10.43.21.12 
Command: config dnsr add static dns1 10.43.21.12 
 

Success. 
 

DES-3326SR:4#

 

 

 
 
 
 
 
 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Ubisys S1 Reference Manual preview
S1
Brand: Ubisys Pages: 40
FANATEC PODIUM Quick Manual preview
PODIUM
Brand: FANATEC Pages: 40
Dataprobe iBoot-G2 Instructions Manual preview
iBoot-G2
Brand: Dataprobe Pages: 21
Cabletron Systems 3T01-04 User Manual preview
3T01-04
Brand: Cabletron Systems Pages: 52
Elements LINQ LQ48006 Product Manual preview
LINQ LQ48006
Brand: Elements Pages: 2
Kobold TDD Operating Instructions Manual preview
TDD
Brand: Kobold Pages: 23
FIBERROAD FR-6R3204 User Manual preview
FR-6R3204
Brand: FIBERROAD Pages: 30
I-Tech AVS801 User Manual preview
AVS801
Brand: I-Tech Pages: 22
ATEN Master View CS-102 User Manual preview
Master View CS-102
Brand: ATEN Pages: 11
FS S5850-24S2C Quick Start Manual preview
S5850-24S2C
Brand: FS Pages: 43
Wyrestorm MXV-0408-H2A v2 Quick Start Manual preview
MXV-0408-H2A v2
Brand: Wyrestorm Pages: 4
AVG AVG-TMX88PRO Manual preview
AVG-TMX88PRO
Brand: AVG Pages: 41
ITC Audio T-6225 Operation Manual preview
T-6225
Brand: ITC Audio Pages: 12
D-Link H4SMK - DSB Hub User Manual preview
H4SMK - DSB Hub
Brand: D-Link Pages: 7
D-Link SmartPro DGS-1510-52XMP Getting Started Manual preview
SmartPro DGS-1510-52XMP
Brand: D-Link Pages: 12
D-Link xStack DGS-3420-28SC Quick Installation Manual preview
xStack DGS-3420-28SC
Brand: D-Link Pages: 22
D-Link GO-SW-8GE Quick Install Manual preview
GO-SW-8GE
Brand: D-Link Pages: 1
D-Link KOMFY Quick Installation Manual preview
KOMFY
Brand: D-Link Pages: 2

Brands by name

Popular brands

Load more brands