manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

328

 

OSPF Configuration Commands 

 

 

config ospf ipif 

Purpose 

Used  to  configure  the  OSPF  interface 
settings. 

Syntax 

config ospf ipif <ipif_name> {area 
<area_id>/priority <value>/hello_interval 
<sec>/dead_interval <sec>/authentication 
[none/simple <password>/md5 
<key_id>]/metric <value>/state 
[enabled/disabled]} 

Description 

This  command  is  used  to  configure  the 
OSPF interface settings. 

Parameters 

<ipif_name> 

−

 The name of the IP interface. 

priority  <value> 

−

  The  priority  used  in  the 

election  of  the  Designated  Router  (DR).    A 
number between 0 and 255. 

metric  <value> 

−

  The  interface  metric  (1  to 

65535).    Entering  a  0  will  allow  automatic 
calculation of the metric. 

hello_interval 

<sec> 

−

 

Allows 

the 

specification  of  the  interval  between  the 
transmission  of  OSPF  Hello  packets,  in 
seconds.  Between 5 and 65535 seconds can 
be  specified.    The  Hello  Interval,  Dead 
Interval, 

Authorization 

Type, 

and 

Authorization Key should be the same for all 
routers on the same network. 

dead_interval 

<sec> 

−

 

Allows 

the 

specification  of  the  length  of  time  between 
the receipt of Hello packets from a neighbor 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

D-Link xStack User Manual preview
xStack
Brand: D-Link Pages: 357
GE GuardSwitch 300 Series Quick Start Manual preview
GuardSwitch 300 Series
Brand: GE Pages: 4
GE SE-100E Instructions Manual preview
SE-100E
Brand: GE Pages: 20
Hama S2100 Operating Instruction preview
S2100
Brand: Hama Pages: 18
Daxten SCOUTCOMBO - Installation Manual preview
SCOUTCOMBO -
Brand: Daxten Pages: 7
KanexPro MX-HDBT8X818G Manual preview
MX-HDBT8X818G
Brand: KanexPro Pages: 16
Maipu SM3100-28TC-AC Installation Manual preview
SM3100-28TC-AC
Brand: Maipu Pages: 21
Maico MVS 6 Mounting And Operating Instructions preview
MVS 6
Brand: Maico Pages: 56
SMC Networks PF2A7 Series Operation Manual preview
PF2A7 Series
Brand: SMC Networks Pages: 43
GarrettCom Magnum 8000X Installation And User Manual preview
Magnum 8000X
Brand: GarrettCom Pages: 63
Gefen EXT-DP-EDIDP User Manual preview
EXT-DP-EDIDP
Brand: Gefen Pages: 56
Allen-Bradley 105-C09 Series Installation Instruction preview
105-C09 Series
Brand: Allen-Bradley Pages: 2
Cabletron Systems SmartSTACK ETHERNET ELS10-27 User Manual preview
SmartSTACK ETHERNET ELS10-27
Brand: Cabletron Systems Pages: 126
Aruba Instant On 1930 Series Installation, Safety, And Regulatory Information preview
Instant On 1930 Series
Brand: Aruba Pages: 8
NegoRack NR-MSR2701S User Manual preview
NR-MSR2701S
Brand: NegoRack Pages: 41
STI SS2 2 Series Manual preview
SS2 2 Series
Brand: STI Pages: 2
Dahua D-PFS4226-24ET-240 Quick Start Manual preview
D-PFS4226-24ET-240
Brand: Dahua Pages: 16
asas Motoroll Manual preview
Motoroll
Brand: asas Pages: 25

Brands by name

Popular brands

Load more brands