manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

DNS Relay Commands 

265 

 

To delete an entry domain name dns1, IPaddress 10.43.21.12 
from DNS static table. 

 

 

 

DES-3326SR:4#config dnsr delete static dns1 10.43.21.12 
Command: config dnsr delete static dns1 10.43.21.12 

 
Success. 
 

DES-3326SR:4#

 

 

enable dnsr 

Purpose 

Used to enable DNS relay. 

Syntax 

enable dnsr 

Description 

This command is used, in combination with 
the disable  dnsr  command below, to enable 
and disable DNS Relay on the switch. 

Parameters 

none. 

Restrictions 

Only  administrator-level  users  can  issue 
this command. 

Example Usage: 

To enable status of DNS relay: 

 

 

 

DES-3326SR:4#enable dnsr 
Command: enable dnsr 

 

Success. 

 
DES-3326SR:4#

 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Nectarine Health Satellite Manual preview
Satellite
Brand: Nectarine Health Pages: 9
Zektor CVS4 User Manual Supplement preview
CVS4
Brand: Zektor Pages: 17
Movie Vision VCS-3 Installation And User Manual preview
VCS-3
Brand: Movie Vision Pages: 2
SMC Networks SMC8724-10BT Technical Specifications preview
SMC8724-10BT
Brand: SMC Networks Pages: 2
Omega Engineering PSW32 SERIES User Manual preview
PSW32 SERIES
Brand: Omega Engineering Pages: 8
Fairchild FSD210 Operator'S Manual preview
FSD210
Brand: Fairchild Pages: 19
Brocade Communications Systems TurboIron 24X series Hardware Installation Manual preview
TurboIron 24X series
Brand: Brocade Communications Systems Pages: 82
Manhattan 177290 User Manual preview
177290
Brand: Manhattan Pages: 4
H3C S5560S-EI Series Configuration Manual preview
S5560S-EI Series
Brand: H3C Pages: 47
Konig CMP-KVMSWIT50 Manual preview
CMP-KVMSWIT50
Brand: Konig Pages: 40
J-Tech Digital JTD-3003 User Manual preview
JTD-3003
Brand: J-Tech Digital Pages: 13
IOGear GCS1808H Quick Start Manual preview
GCS1808H
Brand: IOGear Pages: 12
Magnetrol TD1 Series Installation And Operating Manual preview
TD1 Series
Brand: Magnetrol Pages: 32
Pilz 542 183 Operating Manual preview
542 183
Brand: Pilz Pages: 41
Blackbird 21875 Manual preview
21875
Brand: Blackbird Pages: 19
Qlogic SilverStorm 9120 Quick Start Manual preview
SilverStorm 9120
Brand: Qlogic Pages: 16
CYP OR-HD62CD-4K22 Operation Manual preview
OR-HD62CD-4K22
Brand: CYP Pages: 32
Whelen Engineering Company PCCS9RW Installation Manual preview
PCCS9RW
Brand: Whelen Engineering Company Pages: 5

Brands by name

Popular brands

Load more brands