D-Link DES-3326SRM Command Line Interface Reference Manual Download Page 239

Page: 239 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

IGMP Snooping Commands

239

IGMP S

NOOPING

OMMANDS

The switch port commands in the Command Line Interface (CLI)
are listed (along with the appropriate parameters) in the following
table.

Command

Parameters

config
igmp_snooping

<vlan_name>
all
host_timeout <sec>
router_timeout <sec>
leave_timer <sec>
state [enabled/disabled]

config
igmp_snooping
querier

<vlan_name>
all
query_interval <sec>
max_response_time <sec>
robustness_variable <value>
last_member_query_interval <sec>
state [enabled/disabled]

config router_ports

<vlan_name> [add/delete]
<portlist>

enable
igmp_snooping

forward_mcrouter_only

show
igmp_snooping

vlan <vlan_name>

show
igmp_snooping
group

vlan <vlan_name>

show router_ports

vlan <vlan_name>
static

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Search results

Summary of Contents for DES-3326SRM

Reviews:

Brands by name

Popular brands

D-Link DES-3326SRM, Command Line Interface Reference Manual

Search results

Summary of Contents for DES-3326SRM

Reviews:

Brands by name

Popular brands