manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

Share
Download
D-Link DES-3326SRM Command Line Interface Reference Manual Download Page 338

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

338

 

OSPF Configuration Commands 

 

create ospf virtual_link 

Parameters 

<area_id> 

−

 A 32-bit number in the form of 

an  IP  address  (xxx.xxx.xxx.xxx)  that 
uniquely  identifies  the  OSPF  area  in  the 
OSPF domain. 

<neighbor_id> 

−

  The  OSPF  router  ID  for 

the  remote  area.    This  is  a  32-bit  number 
in 

the 

form 

of 

an 

IP 

address 

(xxx.xxx.xxx.xxx)  that  uniquely  identifies 
the remote area

’

s Area Border Router. The 

router ID of the neighbor router. 

hello_interval 

<sec> 

−

 

Allows 

the 

specification  of  the  interval  between  the 
transmission  of  OSPF  Hello  packets,  in 
seconds.    Between  5  and  65535  seconds 
can be specified.  The Hello Interval, Dead 
Interval, 

Authorization 

Type, 

and 

Authorization  Key  should  be  the  same  for 
all routers on the same network. 

dead_interval  <sec> 

−

  dead_interval  <sec> 

−

  Allows  the  specification  of  the  length  of 

time  between  the  receipt  of  Hello  packets 
from  a  neighbor  router  before  the  selected 
area  declares  that  router  down.    An 
interval between 5 and 65535 seconds can 
be  specified.    The  Dead  Interval  must  be 
evenly divisible by the Hello Interval. 

<password> 

−

 A case-sensitive password. 

<key_id> 

−

  A  previously  configured  MD5 

key ID (1 to 255). 

Restrictions 

Only  administrator-level  users  can  issue 
this command. 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands