manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

138

 

Forwarding Database Commands 

 

create multicast_fdb 

Purpose 

Used to create a static entry to the multicast 
MAC address forwarding table (database) 

Syntax 

create multicast_fdb <vlan_name> 
<macaddr> 

Description 

This command will make an entry into the 
switch

’

s multicast MAC address forwarding 

database. 

Parameters 

<vlan_name> 

−

 The name of the VLAN on 

which the MAC address resides. 

<macaddr> 

−

 The MAC address that will be 

added to the forwarding table. 

Restrictions 

Only administrator-level users can issue 
this command. 

 

Example Usage: 

To create multicast MAC forwarding: 

 

DES-3326SR:4#create multicast_fdb default 01-00-5E-00-00-00 
Command: create multicast_fdb default 01-00-5E-00-00-00 
  

Success. 
 

DES-3326SR:4# 

 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

FELA SWITCH CASAMBI Operation And Installation Manual preview
SWITCH CASAMBI
Brand: FELA Pages: 13
Harman Kardon ABH 4000 Owner'S Manual preview
ABH 4000
Brand: Harman Kardon Pages: 2
IBM 8271 Nways Ethernet LAN Switch User Manual preview
8271 Nways Ethernet LAN Switch
Brand: IBM Pages: 210
N-Tron 608MFX-ST Specifications preview
608MFX-ST
Brand: N-Tron Pages: 2
United Electric Controls 54 Series Assembly, Installation And Operation Instructions preview
54 Series
Brand: United Electric Controls Pages: 6
National Instruments SCXI-1127 Getting Started Manual preview
SCXI-1127
Brand: National Instruments Pages: 32
Balluff IO-Link BNI LH1-303-S11-K091 Installation Manual preview
IO-Link BNI LH1-303-S11-K091
Brand: Balluff Pages: 12
Cabletron Systems MMAC-Plus 9H423-26 Supplementary Manual preview
MMAC-Plus 9H423-26
Brand: Cabletron Systems Pages: 14
3Com Gigabit Switch 8 Specifications preview
Gigabit Switch 8
Brand: 3Com Pages: 2
Zektor HDA800 User Manual preview
HDA800
Brand: Zektor Pages: 65
Zamel GRL-01 Instruction Manual preview
GRL-01
Brand: Zamel Pages: 4
e+p UHD 131 Manual preview
UHD 131
Brand: e+p Pages: 2
S&T kontron KSwitch D4 MF User Manual preview
kontron KSwitch D4 MF
Brand: S&T Pages: 100
I-Tech NVCIP800 User Manual preview
NVCIP800
Brand: I-Tech Pages: 29
Pilz PSEN 1.2p-25 Operating Instructions Manual preview
PSEN 1.2p-25
Brand: Pilz Pages: 8
Eaton NZM3-XTVD-HS Instruction Leaflet preview
NZM3-XTVD-HS
Brand: Eaton Pages: 5
Intel Express 550F User Manual preview
Express 550F
Brand: Intel Pages: 162
C4i HDC-SPB116 User Manual preview
HDC-SPB116
Brand: C4i Pages: 7

Brands by name

Popular brands

Load more brands