D-Link DES-3326SRM Page 139 Command Line Interface Reference Manual Download | Manualshive

Page: 139 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Forwarding Database Commands

139

config multicast_fdb

Purpose

Used to configure the switch

’

s multicast

MAC address forwarding database.

Syntax

config multicast_fdb <vlan_name>
<macaddr> [add/delete] <portlist>

Description

This command configures the multicast
MAC address forwarding table.

Parameters

<vlan_name>

−

The name of the VLAN on

which the MAC address resides.

<macaddr>

−

The MAC address that will be

added to the forwarding table.

[add/delete]

−

Add will add the MAC address

to the forwarding table, delete will remove
the MAC address from the forwarding table.

<portlist>

−

Specifies a range of ports to be

configured. The port list is specified by
listing the lowest switch number and the
beginning port number on that switch,
separated by a colon. Then highest switch
number, and the highest port number of the
range (also separated by a colon) are
specified. The beginning and end of the port
list range are separated by a dash. For
example, 1:3 would specify switch number
1, port 3. 2:4 specifies switch number 2,
port 4. 1:3-2:4 specifies all of the ports
between switch 1, port 3 and switch 2, port
4

−

in numerical order.

Restrictions

Only administrator-level users can issue
this command.

«
...
137
138
139
140
141
...
»

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

GuardSwitch 300 Series

Brand: GE Pages: 4

Brand: GE Pages: 36

Brand: GE Pages: 8

Brand: Qlogic Pages: 135

SANbox2 SANbox2-64

Brand: Qlogic Pages: 224

DES-3224 - Switch

Brand: D-Link Pages: 75

Brand: N-Tron Pages: 158

Unified Gigabit Wireless PoE Switch 24...

Brand: 3Com Pages: 40

IES8242MPp9H-S-DR

Brand: OTS Pages: 3

Brand: N-Tron Pages: 169

Brand: Articona Pages: 2

Brand: Lindy Pages: 54

Brand: Opengear Pages: 109

Brand: Edimax Pages: 8

TK-423K - USB/PS/2 KVM Switch

Brand: TRENDnet Pages: 14

Brand: NVision Pages: 92

Brand: Generac Power Systems Pages: 2

OSD2251P Series

Brand: Optical Systems Design Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands