manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

182

 

VLAN Commands 

 

 

disable gvrp 

Purpose 

Used to disable GVRP on the switch. 

Syntax 

disable gvrp 

Description 

This command, along with disable gvrp 
below, is used to enable and disable GVRP 
on the switch 

−

 without changing the GVRP 

configuration on the switch. 

Parameters 

none. 

Restrictions 

Only administrator-level users can issue 
this command. 

 

Example Usage: 

To disable the Generic VLAN Registration Protocol (GVRP):  

 

 

DES-3326SR:4#disable gvrp 
Command: disable gvrp 
 
 Success. 
 
DES-3326SR:4#

 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

S&C 2000 series Instructions For Field Assembly And Installation preview
2000 series
Brand: S&C Pages: 26
S&C 2000 series Installation And Operation Manual preview
2000 series
Brand: S&C Pages: 37
S&C 2000 series Installation Manual preview
2000 series
Brand: S&C Pages: 28
Datavideo SE-1000 Reference Manual preview
SE-1000
Brand: Datavideo Pages: 4
Datavideo SE-1200MU Quick Start Manual preview
SE-1200MU
Brand: Datavideo Pages: 66
wavin neoHub Quick Start Manual preview
neoHub
Brand: wavin Pages: 4
Cabletron Systems SMALL OFFICE CyberSwitch 150 Manual preview
SMALL OFFICE CyberSwitch 150
Brand: Cabletron Systems Pages: 106
UfiSpace S9180-32X Hardware Installation Manual preview
S9180-32X
Brand: UfiSpace Pages: 25
Equip Vision 332702 Manual preview
Vision 332702
Brand: Equip Pages: 10
Allied Telesis CentreCOM GS970M Series Quick Installation Manual preview
CentreCOM GS970M Series
Brand: Allied Telesis Pages: 21
GarrettCom DS60s Installation And User Manual preview
DS60s
Brand: GarrettCom Pages: 39
JAR Systems MD-5135 Installing preview
MD-5135
Brand: JAR Systems Pages: 2
Surefire ST07 User Manual preview
ST07
Brand: Surefire Pages: 2
Watchguard XTM 3 Series Hardware Manual preview
XTM 3 Series
Brand: Watchguard Pages: 26
CYP OR-HD88HC Operation Manual preview
OR-HD88HC
Brand: CYP Pages: 20
Ormazabal velatia cgm.3 system General Instructions Manual preview
velatia cgm.3 system
Brand: Ormazabal Pages: 76
Planet WGSW-5240 Specifications preview
WGSW-5240
Brand: Planet Pages: 2
AMX AVS-OCT-4832-117 Product View preview
AVS-OCT-4832-117
Brand: AMX Pages: 1

Brands by name

Popular brands

Load more brands