manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

244

 

IGMP Snooping Commands 

 

config igmp_snooping querier 

• 

Last  member  query  count

—

Number 

of  group-specific  queries  sent  before 
the router assumes there are no local 
members  of  a  group.  The  default 
number  is  the  value  of  the 
robustness variable.  

• 

By default, the robustness variable is 
set to 2. You  might  want  to  increase 
this  value  if  you  expect  a  subnet  to 
be lossy.  

last_member_query_interval <sec> 

−

 The  

maximum amount of time between group-
specific query messages, including those 
sent in response to leave-group messages. 
You might lower this interval to reduce the 
amount of time it takes a router to detect 
the loss of the last member of a group

. 

state [enabled/disabled] 

−

  Allows  the  switch 

to  be  specified  as  an  IGMP  Querier  or  Non-
querier. 

Restrictions 

Only  administrator-level  users  can  issue 
this command. 

 

 

 

 

 

 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

GE SecoGear User Manual preview
SecoGear
Brand: GE Pages: 36
GE Power Break Installation Instructions Manual preview
Power Break
Brand: GE Pages: 8
IBM RackSwitch G8264 Product Manual preview
RackSwitch G8264
Brand: IBM Pages: 20
IBM Flex System FC3171 Installation And User Manual preview
Flex System FC3171
Brand: IBM Pages: 64
CAME FROG PLUS Manual preview
FROG PLUS
Brand: CAME Pages: 2
Dahua D-PFS4226-24ET-240 Web Operation Manual preview
D-PFS4226-24ET-240
Brand: Dahua Pages: 58
Hama Data Switch Operating Instruction preview
Data Switch
Brand: Hama Pages: 10
StarTech.com MSTCDP122DP Quick Start Manual preview
MSTCDP122DP
Brand: StarTech.com Pages: 2
Ruby Tech GS-1148L Technical Specifications preview
GS-1148L
Brand: Ruby Tech Pages: 2
GeoVision GV-POE2411-V2 Manual preview
GV-POE2411-V2
Brand: GeoVision Pages: 7
ICCN WX7020-1210G Web User Manual preview
WX7020-1210G
Brand: ICCN Pages: 48
Madison M8000-C Installation And Maintenance preview
M8000-C
Brand: Madison Pages: 2
H3C S5500-28C-EI Installation Manual preview
S5500-28C-EI
Brand: H3C Pages: 96
NVision NV8288 User Manual preview
NV8288
Brand: NVision Pages: 86
Digital China Networks DCRS-5200 Series Specifications preview
DCRS-5200 Series
Brand: Digital China Networks Pages: 4
Byte Delight ZX-HD Manual preview
ZX-HD
Brand: Byte Delight Pages: 12
A SYSTEMS AV800HD User Manual preview
AV800HD
Brand: A SYSTEMS Pages: 80
AMX AVS-OP-1616-567SD Product View preview
AVS-OP-1616-567SD
Brand: AMX Pages: 1

Brands by name

Popular brands

Load more brands