manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

268

 

DNS Relay Commands 

 

 

disable dnsr cache 

Purpose 

Used to disable the DNS relay cache. 

Syntax 

disable dnsr cache 

Description 

This command is used, in combination with 
the  enable  dnsr  cache  command  above,  to 
enable and disable the DNS relay cache. 

Parameters 

none. 

Restrictions 

Only  administrator-level  users  can  issue 
this command. 

 

Example Usage: 

To disable cache lookup for DNS relay. 

 

DES-3326SR:4#disable dnsr cache 
Command: disable dnsr cache 
 

Success. 

 
DES-3326SR:4#

 

 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Omega Engineering 430 Instruction Sheet preview
430
Brand: Omega Engineering Pages: 3
KanexPro MX-HDBT8X818G Manual preview
MX-HDBT8X818G
Brand: KanexPro Pages: 16
IOGear MicroHub GUH274W3 (Portuguese) Manual Do Usuário preview
MicroHub GUH274W3
Brand: IOGear Pages: 1
Kramer XL 1204V2 Specifications preview
XL 1204V2
Brand: Kramer Pages: 2
Orno OR-GB-422 Quick Start Manual preview
OR-GB-422
Brand: Orno Pages: 2
StarTech.com 8STSV231DDVDUA Manual preview
8STSV231DDVDUA
Brand: StarTech.com Pages: 16
Davey RainBank Installation Instructions preview
RainBank
Brand: Davey Pages: 2
HDTV Supply HDTVMT0808140 User Manual preview
HDTVMT0808140
Brand: HDTV Supply Pages: 21
SLV 470819 Quick Installation Manual preview
470819
Brand: SLV Pages: 22
Edimax EK-PS2P User Manual preview
EK-PS2P
Brand: Edimax Pages: 3
steute EM 61 Mounting And Wiring Instructions preview
EM 61
Brand: steute Pages: 12
SK telecom HPS-1004GP User Manual preview
HPS-1004GP
Brand: SK telecom Pages: 7
Stahl 8537/2 Operating Instructions Manual preview
8537/2
Brand: Stahl Pages: 28
Festo SMT-8-...-B Series Manual preview
SMT-8-...-B Series
Brand: Festo Pages: 2
ClimaxDigital CHM0402V3 User Manual preview
CHM0402V3
Brand: ClimaxDigital Pages: 9
Luminex DMX512-A 2.10 HUB User Manual preview
DMX512-A 2.10 HUB
Brand: Luminex Pages: 12
AVLink HX-2444 User Manual preview
HX-2444
Brand: AVLink Pages: 72
TV One IM-400 Series Instruction Manual preview
IM-400 Series
Brand: TV One Pages: 32

Brands by name

Popular brands

Load more brands