D-Link DES-3326SRM Command Line Interface Reference Manual Download | Manualshive

Page: 201 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

IP Interface Commands

201

config ipif System

Purpose

Used to configure the System IP interface.

Syntax

config ipif System [{vlan
<vlan_name>/ipaddress
<network_address>/state
[enabled/disabled]/bootp/dhcp}]

Description

This command is used to configure the
System IP interface on the switch.

Parameters

<vlan_name>

−

The name of the VLAN

corresponding to the System IP interface.

<network_address>

−

IP address and

netmask  of  the  IP  interface  to  be  created.
You  can  specify  the  address  and  mask
information using the  traditional format (for
example,  10.1.2.3/255.0.0.0  or  in  CIDR
format, 10.1.2.3/16).

state [enabled/disabled]

−

Allows you to

enable or disable the IP interface.

bootp

−

Allows the selection of the BOOTP

protocol for the assignment of an IP address
to the switch

’

s System IP interface.

dhcp

−

Allows the selection of the DHCP

protocol for the assignment of an IP address
to the switch

’

s System IP interface.

Restrictions

Only administrator-level users can issue
this command.

«
...
199
200
201
202
203
...
»

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

EtherDevice EDS-4009 Series

Brand: Moxa Technologies Pages: 18

Brand: TP-Link Pages: 2

Brand: IOGear Pages: 10

PAT TRS 05 / PATB3

Brand: Hirschmann Pages: 12

Brand: UNICOM Pages: 1

AVS-OCT-6448-210

Brand: AMX Pages: 1

Brand: Eaton Pages: 36

Brand: UNICOM Pages: 15

Brand: KanexPro Pages: 35

Brand: C&C TECHNIC Pages: 2

Brand: KinAn Pages: 5

Brand: Dahua Pages: 12

Brand: LevelOne Pages: 15

Brand: Voith Pages: 98

SmartSTACK ELS100-24TXG

Brand: Cabletron Systems Pages: 7

Brand: Opencockpits Pages: 30

Brand: CityGrow Systems Pages: 21

Brand: Gefen Pages: 136

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands