D-Link DES-3326SRM Command Line Interface Reference Manual Download | Manualshive

Page: 157 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

QOS Commands

157

config scheduling

specify the maximum amount of time that
packets will be delayed before being
transmitted. For a given priority queue, a
value between 0 and 255 can be specified.
This number is then multiplied by 16
milliseconds to determine the maximum
allowed latency. For example, if 3 is
specified for queue 0, the maximum latency
allowed will be 3 X 16 ms = 48 ms. When
queue 0 has been waiting to transmit
packets for longer than 48 ms, the currently
transmitting priority queue is allowed to
finish transmitting its current packet, and
then queue 0 is allowed to begin
transmitting its packets.

Parameters

<class_id>

−

Specifies which of the four

priority queues the config scheduling
command will be applied to. The four
priority queues are identified by number

−

from 0 to 3

−

with queue 0 being the highest

priority.
max_packet <value 0-255>

−

Specifies the

maximum number of packets the above
specified priority queue will be allowed to
transmit before allowing the next lowest
priority queue to transmit its packets. A
value between 0 and 255 packets can be
specified.
max_latency <value 0-255>

−

Specifies the

maximum amount of time the above
specified priority queue will have to wait

«
...
155
156
157
158
159
...
»

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Brand: B&B Electronics Pages: 26

Brand: B&B Electronics Pages: 15

Brand: B&B Electronics Pages: 45

Brand: Radial Engineering Pages: 12

Brand: ORiNG Pages: 2

TECMA Silence Marine

Brand: Thetford Marine Pages: 9

Brand: Touch-plate Pages: 12

Brand: hager Pages: 4

3C16710 - OfficeConnect 8/TPM Hub

Brand: 3Com Pages: 130

Brand: Accton Technology Pages: 523

Brand: Orno Pages: 2

852-1411/000-001

Brand: WAGO Pages: 40

Brand: 3Com Pages: 74

Brand: Digitus Pages: 10

Brand: Abtus Pages: 4

Brand: PortaOne Pages: 78

Brand: Pakedge Device & Software Pages: 8

Brand: Black Box Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands