manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

110

 

Network Monitoring Commands 

 

 
 

enable syslog 

Purpose 

Used to enable the system log to be sent to a 
remote host. 

Syntax 

enable syslog 

Description 

The enable syslog command enables the 
system log to be sent to a remote host. 

Parameters 

None. 

Restrictions 

Only administrator-level users can issue 
this command. 

 

Example Usage: 

To the syslog function on the switch: 

DES-3326SR:4#enable syslog 
Command: enable syslog 
 
 Success. 
 
DES-3326SR:4# 

 
 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

D-Link DGS-1024D - Switch Quick Installation Manual preview
DGS-1024D - Switch
Brand: D-Link Pages: 16
D-Link DGS-1016D - Switch User Manual preview
DGS-1016D - Switch
Brand: D-Link Pages: 44
D-Link DES-6000 Series Firmware Update Manual preview
DES-6000 Series
Brand: D-Link Pages: 3
D-Link DES-5024 - Switch Application Notes preview
DES-5024 - Switch
Brand: D-Link Pages: 2
D-Link DES-3828 - xStack Switch - Stackable Datasheet preview
DES-3828 - xStack Switch - Stackable
Brand: D-Link Pages: 3
D-Link DES-3550 User Manual preview
DES-3550
Brand: D-Link Pages: 192
D-Link DES-3326 Configuration Manual preview
DES-3326
Brand: D-Link Pages: 9
D-Link DES-3226L User Manual preview
DES-3226L
Brand: D-Link Pages: 110
D-Link DES-1026G User Manual preview
DES-1026G
Brand: D-Link Pages: 10
D-Link DES-1008D Manual preview
DES-1008D
Brand: D-Link Pages: 17
D-Link DES-1005P Quick Install Manual preview
DES-1005P
Brand: D-Link Pages: 4
D-Link DGS-1210-28P Manual preview
DGS-1210-28P
Brand: D-Link Pages: 9
D-Link DES-1024D Brochure preview
DES-1024D
Brand: D-Link Pages: 4
D-Link DGS-105 - Switch Datasheet preview
DGS-105 - Switch
Brand: D-Link Pages: 4
D-Link DES-1024D Quick Install Manual preview
DES-1024D
Brand: D-Link Pages: 2
D-Link des-1016a Quick Install Manual preview
des-1016a
Brand: D-Link Pages: 2
IBM N Series Setup And Configuration Manual preview
N Series
Brand: IBM Pages: 44
IDK MSD-804FD Series Command Manual preview
MSD-804FD Series
Brand: IDK Pages: 133

Brands by name

Popular brands

Load more brands