manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

Share
Download
D-Link DES-3326SRM Command Line Interface Reference Manual Download Page 85

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

Network Management Commands 

85 

 

 
 
 
 

enable rmon 

Purpose 

Used to enable RMON on the switch. 

Syntax 

enable rmon 

Description 

This  command  is  used,  in  conjunction 
with the disable rmon command below, to 
enable  and  disable  remote  monitoring 
(RMON) on the switch. 

Parameters 

none. 

Restrictions 

Only  administrator-level  users  can  issue 
this command. 

 

Example Usage

: 

 

DES-3326SR:4#enable rmon 
Command: enable rmon 
 
 Success. 
 
DES-3326SR:4# 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands