D-Link DES-3326SRM Page 77 Command Line Interface Reference Manual Download

Page: 77 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Network Management Commands

create snmp group

be used. SNMP v3 provides secure access
to devices through a combination of
authentication and encrypting packets over
the network. SNMP v3 adds:

•

Message integrity

−

ensures that

packets have not been tampered
with in transit.

•

Authentication

−

determines that an

SNMP message is from a valid
source.

•

Encryption

−

scrambles the contents

of messages to prevent it being seen
by an unauthorized source.

noauth_nopriv

−

Specifies that there

will be no authorization and no
encryption of packets sent between the
switch and a remote SNMP manager.

auth_nopriv

−

Specifies that

authorization will be required, but
there will be no encryption of packets
sent between the switch and a remote
SNMP manager.

auth_priv

−

Specifies that authorization

will be required, and that packets sent
between the swtich and a remote SNMP
manger will be encrypted.

read_view

–

Specifies that the SNMP group

being created can request SNMP messages.

<view_name 32>

−

An alphanumeric

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Search results

Summary of Contents for DES-3326SRM

Reviews:

Related manuals for DES-3326SRM

Brands by name

Popular brands

D-Link DES-3326SRM, Command Line Interface Reference Manual

Search results

Summary of Contents for DES-3326SRM

Reviews:

Related manuals for DES-3326SRM

Brands by name

Popular brands