D-Link DES-3326SRM Page 257 Command Line Interface Reference Manual Download

Page: 257 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Bootp Relay Commands

257

config bootp_relay add

Purpose

Used to add an IP destination address to the
switch

’

s BOOTP relay table.

Syntax

config bootp_relay add ipif <ipif_name>
<ipaddr>

Description

This command adds an IP address as a
destination to forward (relay) BOOTP
packets to.

Parameters

<ipif_name>

−

The name of the IP interface

which contains the IP address below.

−

The BOOTP server IP address.

Restrictions

Only administrator-level users can issue
this command.

Example Usage:

To add a BOOTP relay.

DES-3326SR:4#config bootp_relay add ipif System 10.43.21.12
Command: config bootp_relay add ipif System 10.43.21.12

Success.

DES-3326SR:4#

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Search results

Summary of Contents for DES-3326SRM

Reviews:

Related manuals for DES-3326SRM

Brands by name

Popular brands

D-Link DES-3326SRM, Command Line Interface Reference Manual

Search results

Summary of Contents for DES-3326SRM

Reviews:

Related manuals for DES-3326SRM

Brands by name

Popular brands