D-Link DES-3326SRM Page 210 Command Line Interface Reference Manual Download | Manualshive

Page: 210 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

210

Arp Commands

delete arpentry

Purpose

Used to delete a static entry into the ARP
table.

Syntax

delete arpentry {<ipaddr>/all}

Description

This command is used to delete a static ARP
entry,  made  using  the  create  arpentry
command above, by specifying either  the  IP
address  of  the  entry  or  all.    Specifying  all
clears the switch

’

s ARP table.

Parameters

<ipaddr>

−

The IP address of the end node

or station.

all

−

deletes all ARP entries.

Restrictions

Only administrator-level users can issue
this command.

Example Usage:

To delete an entry of IP address 10.48.74.121 from the ARP
table:

DES-3326SR:4#delete arpentry 10.48.74.121
Command: delete arpentry 10.48.74.121

Success.

DES-3326SR:4#

«
...
208
209
210
211
212
...
»

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Brand: Matrix Switch Corporation Pages: 60

Brand: Erbe Pages: 118

Raritan Dominion LX II

Brand: LEGRAND Pages: 7

Brand: Crestron Pages: 2

TM-1-8210 Series

Brand: Eaton Pages: 3

Premasreg 716 Series

Brand: S+S Regeltechnik Pages: 32

Guard Master 440N-Z2NRS1A

Brand: Allen-Bradley Pages: 4

Brand: QSFPTEK Pages: 12

Brand: Davey Pages: 2

Brand: Velleman Pages: 8

Brand: X-keys Pages: 4

Brand: senva Pages: 2

Nivotester FTC325

Brand: Endress+Hauser Pages: 40

Brand: TRENDnet Pages: 32

Brand: Qvis Pages: 7

Power Switch G0021

Brand: G-Force Pages: 2

Brand: Stahl Pages: 28

Brand: D+H Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands