manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

152

 

QOS Commands 

 

 

config bandwidth_control 

Purpose 

Used to configure bandwidth control on a 
by-port basis. 

Syntax 

config bandwidth_control <portlist> 
{re_rate [no_limit/<value 1-
1000>]/tx_rate [no_limit/<value 1-
1000>]} 

Description 

The config bandwidth_control command 
configures bandwidth on a by-port basis. 

Parameters 

<portlist> 

−

 Specifies a range of ports to be 

configured. The port list is specified by 
listing the lowest switch number and the 
beginning port number on that switch, 
separated by a colon. Then highest switch 
number, and the highest port number of the 
range (also separated by a colon) are 
specified. The beginning and end of the port 
list range are separated by a dash. For 
example, 1:3 would specify switch number 
1, port 3. 2:4 specifies switch number 2, 
port 4. 1:3-2:4 specifies all of the ports 
between switch 1, port 3 and switch 2, port 
4 

−

 in numerical order. 

rx_rate 

−

 Specifies that one of the 

parameters below (no_limit or <value 1-
1000>) will be applied to the rate at which 
the above specified ports will be allowed to 
receive packets 

no_limit 

−

 Specifies that there will be no 

limit on the rate of packets received by 
the above specified ports. 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Aruba Instant On 1930 24G 4SFP/SFP+l Installation And Getting Started Manual preview
Instant On 1930 24G 4SFP/SFP+l
Brand: Aruba Pages: 48
IOGear GUH420 Quick Start Manual preview
GUH420
Brand: IOGear Pages: 1
FS IES3110-8TF Quick Start Manual preview
IES3110-8TF
Brand: FS Pages: 33
Silent Gliss 0913 Installation, Programming And Operation Instructions preview
0913
Brand: Silent Gliss Pages: 4
KYLAND SICOM3432G Series Hardware Installation Manual preview
SICOM3432G Series
Brand: KYLAND Pages: 29
Global Streams GlobeCaster STUDIO 4000 Manual preview
GlobeCaster STUDIO 4000
Brand: Global Streams Pages: 144
MRD TNM4000-TP36FF4X16G24P User Manual preview
TNM4000-TP36FF4X16G24P
Brand: MRD Pages: 38
Dahua VTNS1006A-2 User Manual preview
VTNS1006A-2
Brand: Dahua Pages: 12
ROSSMA IIOT-AMS Tilt Counter Operation Manual preview
IIOT-AMS Tilt Counter
Brand: ROSSMA Pages: 13
STI SS2 2 Series Manual preview
SS2 2 Series
Brand: STI Pages: 2
Linksys SRW224 - 10/100 - Gigabit Switch Specifications preview
SRW224 - 10/100 - Gigabit Switch
Brand: Linksys Pages: 2
Banner SI-HG63FQDR Instruction Manual preview
SI-HG63FQDR
Brand: Banner Pages: 8
Sensor Switch SPODMRA JOT Installation Instructions preview
SPODMRA JOT
Brand: Sensor Switch Pages: 2
Hama 5-Port Gigabit Switch 1000 Mbps User Manual preview
5-Port Gigabit Switch 1000 Mbps
Brand: Hama Pages: 2
BZB Gear BZ-UHD-88M100-ARC User Manual preview
BZ-UHD-88M100-ARC
Brand: BZB Gear Pages: 42
StarTech.com VS122HDMIU Instruction Manual preview
VS122HDMIU
Brand: StarTech.com Pages: 2
SMART-AVI DVN-4QUAD-DL Quick Start Manual preview
DVN-4QUAD-DL
Brand: SMART-AVI Pages: 2
Cabletron Systems MicroMMAC-24E Installation Manual preview
MicroMMAC-24E
Brand: Cabletron Systems Pages: 83

Brands by name

Popular brands

Load more brands