manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

154

 

QOS Commands 

 

 

show bandwidth_control 

Purpose 

Used to display the bandwidth control 
configuration on the switch. 

Syntax 

show bandwidth_control {<portlist>} 

Description 

The show bandwidth_control command 
displays the current bandwidth control 
configuration on the switch, on a port-by-
port basis. 

Parameters 

<portlist> 

−

 Specifies a range of ports to be 

configured. The port list is specified by 
listing the lowest switch number and the 
beginning port number on that switch, 
separated by a colon. Then highest switch 
number, and the highest port number of the 
range (also separated by a colon) are 
specified. The beginning and end of the port 
list range are separated by a dash. For 
example, 1:3 would specify switch number 
1, port 3. 2:4 specifies switch number 2, 
port 4. 1:3-2:4 specifies all of the ports 
between switch 1, port 3 and switch 2, port 
4 

−

 in numerical order. 

Restrictions 

None. 

 
 
 
 
 
 
 
 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Hama USB Hub Operating Instruction preview
USB Hub
Brand: Hama Pages: 14
Hama Super Speed USB 3.0 Hub Operating Instruction preview
Super Speed USB 3.0 Hub
Brand: Hama Pages: 14
Hama S1110 Operating Instruction preview
S1110
Brand: Hama Pages: 12
Hama 78496 Operating Instruction preview
78496
Brand: Hama Pages: 14
Hama Premium Silver USB 2.0 Hub 1:4 Operating Instruction preview
Premium Silver USB 2.0 Hub 1:4
Brand: Hama Pages: 12
Hama S2110 Operating Instruction preview
S2110
Brand: Hama Pages: 18
Hama uRage Vendetta 210 Manual preview
uRage Vendetta 210
Brand: Hama Pages: 36
UNICOM FEP-31024T-3 Specifications preview
FEP-31024T-3
Brand: UNICOM Pages: 1
Alyseum MS-SW5 User Manual preview
MS-SW5
Brand: Alyseum Pages: 7
ATZ HDMI-161SM Manual preview
HDMI-161SM
Brand: ATZ Pages: 8
Gefen EXT-DVIKVM-441DL User Manual preview
EXT-DVIKVM-441DL
Brand: Gefen Pages: 32
Network Technologies VEEMUX SM-nXm-15V-LC Installation And Operation Manual preview
VEEMUX SM-nXm-15V-LC
Brand: Network Technologies Pages: 46
H3C S12500G-AF Series Installation Manual preview
S12500G-AF Series
Brand: H3C Pages: 105
Kramer DigiTOOLS VS-41USB User Manual preview
DigiTOOLS VS-41USB
Brand: Kramer Pages: 8
TRENDnet TK-205K - PS/2 KVM Switch (German) Anleitung Zur Schnellinstallation preview
TK-205K - PS/2 KVM Switch
Brand: TRENDnet Pages: 11
Homefibre OMS 113- 220 User Manual preview
OMS 113- 220
Brand: Homefibre Pages: 2
Comtech EF Data CRS-280 Installation And Operation Manual preview
CRS-280
Brand: Comtech EF Data Pages: 70
Black Box LGB408A-R2 Manual preview
LGB408A-R2
Brand: Black Box Pages: 20

Brands by name

Popular brands

Load more brands