manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

DNS Relay Commands 

271 

 

 

show dnsr 

Purpose 

Used to display the current DNS relay static 
table. 

Syntax 

show dnsr {static} 

Description 

This command is used to display the current 
DNS relay static table. 

Parameters 

static 

−

 Allows the display  of  only  the  static 

entries  into  the  DNS  relay  table.    If  this 
parameter  is  omitted,  the  entire  DNS  relay 
table will be displayed. 

Restrictions 

none. 

Example Usage: 

To display DNS relay table: 

 

 

 

DES-3326SR:4#show dnsr static 
Command: show dnsr static 
 
DNS Relay Static Table 
Domain Name                        IP Address 
--------------------------------------   --------------- 
www.123.com.tw                  10.12.12.123 
    bbs.ntu.edu.tw                  140.112.1.23 
 
Total Entries: 2 
 
DES-3326SR:4#

 

 
 
 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Cabletron Systems MMAC-Plus 9G426-02 Reference Manual preview
MMAC-Plus 9G426-02
Brand: Cabletron Systems Pages: 12
Cabletron Systems MMAC-Plus 9F310-02 Appendix preview
MMAC-Plus 9F310-02
Brand: Cabletron Systems Pages: 4
Cabletron Systems 9E423-36 Owner'S Manual preview
9E423-36
Brand: Cabletron Systems Pages: 16
cable matters 101065 Quick Start Manual preview
101065
Brand: cable matters Pages: 4
CableCreation CD0395 User Manual preview
CD0395
Brand: CableCreation Pages: 7
Eaton COOPER POWER SERIES Service Instructions Manual preview
COOPER POWER SERIES
Brand: Eaton Pages: 24
Eaton COOPER POWER SERIES Installation And Adjustment Instructions preview
COOPER POWER SERIES
Brand: Eaton Pages: 16
Eaton Crouse-hinds series Manual preview
Crouse-hinds series
Brand: Eaton Pages: 16
Eaton Cutler-Hammer AMPGARD Instructions preview
Cutler-Hammer AMPGARD
Brand: Eaton Pages: 4
Raritan MCCAT18 Specifications preview
MCCAT18
Brand: Raritan Pages: 4
Jasco AS2006 Manual preview
AS2006
Brand: Jasco Pages: 2
Belkin F5U307 User Manual preview
F5U307
Brand: Belkin Pages: 12
3Com 3C63100-AC-C - PathBuilder S600... Reference Manual preview
3C63100-AC-C - PathBuilder S600...
Brand: 3Com Pages: 232
LAPP ETHERLINE ACCESS U04TP01T Hardware Installation Manual preview
ETHERLINE ACCESS U04TP01T
Brand: LAPP Pages: 16
Enterasys RoamAbout RBT-4102-BG Installation Manual preview
RoamAbout RBT-4102-BG
Brand: Enterasys Pages: 72
Eaton LPC25-16FUSE Instruction Leaflet preview
LPC25-16FUSE
Brand: Eaton Pages: 2
Cabletron Systems FlowPoint 2100 12 User Manual preview
FlowPoint 2100 12
Brand: Cabletron Systems Pages: 36
Hawking PN824ES Specifications preview
PN824ES
Brand: Hawking Pages: 2

Brands by name

Popular brands

Load more brands