D-Link DES-3326SRM Command Line Interface Reference Manual Download | Manualshive

Page: 179 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

VLAN Commands

179

config gvrp

Purpose

Used to configure GVRP on the switch.

Syntax

config gvrp [<portlist>/all] {state
[enabled/disabled]/ingress_checking
[enabled/disabled]}

Description

This command is used to configure the
Group VLAN Registration Protocol on the
switch. You can configure ingress checking,
the sending and receiving of GVRP
information, and the Port VLAN ID (PVID).

Parameters

<portlist>

−

A range of ports for which you

want ingress checking. The port list is
specified by listing the lowest switch
number and the beginning port number on
that switch, separated by a colon. Then
highest switch number, and the highest
port number of the range (also separated by
a colon) are specified. The beginning and
end of the port list range are separated by a
dash. For example, 1:3 would specify switch
number 1, port 3. 2:4 specifies switch
number 2, port 4. 1:3-2:4 specifies all of the
ports between switch 1, port 3 and switch 2,
port 4

−

in numerical order.

all

−

Specifies all of the ports on the switch.

state [enabled/disabled]

−

Enables or

disables GVRP for ports in port list.
ingress_checking [enabled/disabled]

−

Enables or disables ingress checking for the
specified port list.

Restrictions

Only administrator-level users can issue
this command.

«
...
177
178
179
180
181
...
»

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

TradeSwitch2-USB

Brand: G&D Pages: 88

Brand: A-Neuvideo Pages: 26

Brand: Accton Technology Pages: 523

Brand: F&F Pages: 10

Brand: Videosec Pages: 5

Safeline 2000 Light

Brand: Hisselektronik Pages: 9

Brand: FS Pages: 43

Brand: Harman Pages: 50

Brand: Tabs Pages: 4

Brand: N-Tron Pages: 2

Ascentic MH10-ARC

Brand: Audio Authority Pages: 5

Brand: Black Box Pages: 3

Brand: WELLTECH Pages: 280

WL-CPE2G24D-075

Brand: Mach Power Pages: 44

Brand: Mastervolt Pages: 2

AVS-OP-2404-210

Brand: AMX Pages: 1

Brand: Mo-vis Pages: 109

Brand: Fujitsu Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands