manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

158

 

QOS Commands 

 

config scheduling 

before being allowed to transmit any 
packets that have accumulated in its 
transmit buffer.  A value between 0 and 255 
can be specified 

−

 with this value being 

multiplied by 16 ms to arrive at the total 
time the priority queue will have to wait. 

Restrictions 

Only administrator-level users can issue 
this command. 

 

Example Usage: 

To create 

DES-3326SR:4# config scheduling 0 max_packet 100 max_latency 
150 
Command: config scheduling 0 max_packet 100 max_latency 150 
 
 Success. 
 
DES-3326SR:4# 

 
 
 
 

show scheduling 

Purpose 

Used to display the currently configured 
traffic scheduling on the switch. 

Syntax 

show scheduling 

Description 

The show scheduling command displays 
the current configuration for the maximum 
number of packets (max_packets) and the 
maximum latency (max_latency) values 
assigned to the four priority queues on the 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Cabletron Systems SmartSwitch 9A100 Installation And Setup Manual preview
SmartSwitch 9A100
Brand: Cabletron Systems Pages: 52
Cabletron Systems SmartSwitch 9W006 Quick Start Manual preview
SmartSwitch 9W006
Brand: Cabletron Systems Pages: 34
Cabletron Systems SmartSTACK ELS100-S24TX2M Management Manual preview
SmartSTACK ELS100-S24TX2M
Brand: Cabletron Systems Pages: 102
Cabletron Systems 9A426-01 Appendix preview
9A426-01
Brand: Cabletron Systems Pages: 24
Cabletron Systems SmartSwitch 9000 Appendix preview
SmartSwitch 9000
Brand: Cabletron Systems Pages: 14
Cabletron Systems MicroMMAC 22ES Reference Manual preview
MicroMMAC 22ES
Brand: Cabletron Systems Pages: 38
Field Controls 46112100 Manual preview
46112100
Brand: Field Controls Pages: 4
Xunison Hub M50 Mesh Cube Quick Start Manual preview
Hub M50 Mesh Cube
Brand: Xunison Pages: 11
Balluff NAMUR BES G06MD-GNX10B-EV02-EEX Operating Instructions Manual preview
NAMUR BES G06MD-GNX10B-EV02-EEX
Brand: Balluff Pages: 56
Exsys EX-1183HMVS-2W Manual preview
EX-1183HMVS-2W
Brand: Exsys Pages: 14
JAR Systems MD-5135 Installing preview
MD-5135
Brand: JAR Systems Pages: 2
Surefire ST07 User Manual preview
ST07
Brand: Surefire Pages: 2
Fortinet FortiSwitch 424E Series Quick Start Manual preview
FortiSwitch 424E Series
Brand: Fortinet Pages: 11
SIIG Hi-Speed USB 4-Port Bay Hub Quick Installation Manual preview
Hi-Speed USB 4-Port Bay Hub
Brand: SIIG Pages: 8
H3C WX3010E Installation Manual preview
WX3010E
Brand: H3C Pages: 70
Black Box Personal MiniHub Manual preview
Personal MiniHub
Brand: Black Box Pages: 22
PIKA mWARP Manual preview
mWARP
Brand: PIKA Pages: 7
N-Tron 702-W Features preview
702-W
Brand: N-Tron Pages: 2

Brands by name

Popular brands

Load more brands