D-Link DES-3326SRM Command Line Interface Reference Manual Download

Page: 120 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

120

Network Monitoring Commands

config syslog host

local1

−

Specifies that local use 1 messages

will be sent to the remote host. This
corresponds to number 17 from the list
above.

local2

−

Specifies that local use 2 messages

will be sent to the remote host. This
corresponds to number 18 from the list
above.

local3

−

Specifies that local use 3 messages

will be sent to the remote host. This
corresponds to number 19 from the list
above.

local4

−

Specifies that local use 4 messages

will be sent to the remote host. This
corresponds to number 20 from the list
above.

local5

−

Specifies that local use 5 messages

will be sent to the remote host. This
corresponds to number 21 from the list
above.

local6

−

Specifies that local use 6 messages

will be sent to the remote host. This
corresponds to number 22 from the list
above.

local7

−

Specifies that local use 7 messages

will be sent to the remote host. This
corresponds to number 23 from the list
above.

udp_port <int>

−

Specifies the UDP port

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Search results

Summary of Contents for DES-3326SRM

Reviews:

Related manuals for DES-3326SRM

Brands by name

Popular brands

D-Link DES-3326SRM, Command Line Interface Reference Manual

Search results

Summary of Contents for DES-3326SRM

Reviews:

Related manuals for DES-3326SRM

Brands by name

Popular brands