manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

Share
Download
D-Link DES-3326SRM Command Line Interface Reference Manual Download Page 295

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

IP Multicasting Commands 

295 

 

show ipmc 

Purpose 

Used  to  display  the  IP  multicast  interface 
table. 

Syntax 

show ipmc {ipif <ipip_name>/protocol 
[dvmrp/pim]} 

Description 

This  command  will  display  the  current  IP 
multicast interface table. 

Parameters 

<ipif_name> 

−

  The  name  of  the  IP  interface 

for  which  you  want  to  display  the  IP 
multicast interface table for. 

protocol [dvmrp/pim] 

−

 Allows you to specify 

either the DVMRP or PIM protocol to be used 
in displaying the IP multicast interface table.  
For example, if DVMRP is specified, the table 
will  display  only  those  entries  that  are 
related to the DVMRP protocol. 

Restrictions 

none. 

Usage Example 

 

To display the current IP multicast interface table: 

DES-3326SR:4#show ipmc 
Command: show ipmc 
 
   Interface       IP Address     Multicast Routing 
---------------       ---------------      ----------------- 
     System       10.90.90.90               INACT 
 
Total Entries: 1 
 
DES-3326SR:4#

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands