manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

212

 

Arp Commands 

 

 

show arpentry 

Purpose 

Used to display the ARP table. 

Syntax 

show  arpentry  {ipif  <ipif_name>/ipaddress 
<network_address>/static} 

Description 

This  command  is  used  to  display  the 
current contents of the switch

’

s ARP table. 

Parameters 

<ipif_name> 

−

  The  name  of  the  IP  interface 

the  end  node  or  station  for  which  the  ARP 
table entry was made, resides on. 

<network_address> 

−

  The  network  address 

corresponding  to  the  IP  interface  name 
above. 

static 

−

  Displays  the  static  entries  to  the 

ARP table. 

Restrictions 

none. 

 

Example Usage: 

To display the ARP table

: 

 

DES-3326SR:4#show arpentry 
Command: show arpentry 
 ARP Aging Time : 30 
 
Interface       IP Address       MAC Address          Type 
-------------      ---------------        -----------------              --------------- 
System         10.0.0.0             FF-FF-FF-FF-FF-FF   Local/Broadcast 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

ABB EDS500 Series Operating Instruction preview
EDS500 Series
Brand: ABB Pages: 7
3Com SuperStack II Important Information preview
SuperStack II
Brand: 3Com Pages: 2
3Com CoreBuilder 5000 Quick Start And Reference preview
CoreBuilder 5000
Brand: 3Com Pages: 16
3Com CoreBuilder 9000 Quick Installation Manual preview
CoreBuilder 9000
Brand: 3Com Pages: 24
Kathrein EXR 221 Quick Start Manual preview
EXR 221
Brand: Kathrein Pages: 8
Nayar Systems Switch Manual preview
Switch
Brand: Nayar Systems Pages: 21
Kathrein EXD 1532 User Manual preview
EXD 1532
Brand: Kathrein Pages: 24
Kasia Switch Installation Manual preview
Switch
Brand: Kasia Pages: 5
Gilat SkyEdge II-c Capricorn Pro 4 AC Series Installation Notes preview
SkyEdge II-c Capricorn Pro 4 AC Series
Brand: Gilat Pages: 2
Touch-plate 10138 Manual preview
10138
Brand: Touch-plate Pages: 12
TAXON TOOLS Scart Switch Manual preview
Scart Switch
Brand: TAXON TOOLS Pages: 9
Cable Electronics HSW44C Plus Instruction Manual preview
HSW44C Plus
Brand: Cable Electronics Pages: 16
Cabletron Systems SmartStack STS16-20R Installation And User Manual preview
SmartStack STS16-20R
Brand: Cabletron Systems Pages: 258
C4i HDC-SPB116 User Manual preview
HDC-SPB116
Brand: C4i Pages: 7
Green Brook KingShield T206-C Installation And Operating Instruction preview
KingShield T206-C
Brand: Green Brook Pages: 2
X-keys XK-60 Product Manual preview
XK-60
Brand: X-keys Pages: 4
senva C-2330 Installation Instructions preview
C-2330
Brand: senva Pages: 2
W2IIHY 3 4 Operating Manual preview
3 4
Brand: W2IIHY Pages: 28

Brands by name

Popular brands

Load more brands