manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

310

 

OSPF Configuration Commands 

 

create ospf area 

[enabled/disabled]/metric <value>}] 

Description 

This  command  is  used  to  create  an  OSPF 
area and configure its settings. 

Parameters 

<area_id> 

−

 The OSPF area ID. 

type 

−

  The  OSPF  area  mode  of  operation 

−

 

stub or normal. 

stub_summary 

−

  enables  or  disables  the 

OSPF  area  to  import  summary  LSA 
advertisements. 

<value> 

−

  The  OSPF  area  cost  between  0 

and 65535.  The default is 0. 

Restrictions 

Only  administrator-level  users  can  issue 
this command. 

Usage Example: 

 

To create an OSPF area: 

DES-3326SR:4#create ospf area 10.48.74.122 type normal 
Command: create ospf area 10.48.74.122 type normal 
 
Success. 
 
DES-3326SR:4#

 

 

 

 

 

 

delete ospf area 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

NEC 2400 Integration Manual preview
2400
Brand: NEC Pages: 168
A SYSTEMS AV50 User Manual preview
AV50
Brand: A SYSTEMS Pages: 16
DANLERS WAPIR Installation Notes preview
WAPIR
Brand: DANLERS Pages: 2
Lindy 32351 Manual preview
32351
Brand: Lindy Pages: 70
socomec ATyS p M Instruction Manual preview
ATyS p M
Brand: socomec Pages: 78
Extron electronics MSW 4SV rs Specifications preview
MSW 4SV rs
Brand: Extron electronics Pages: 2
Westell A99-BAI-ACSF-UGKIT Install Instructions preview
A99-BAI-ACSF-UGKIT
Brand: Westell Pages: 3
SMSC LAN9312 Datasheet preview
LAN9312
Brand: SMSC Pages: 458
Omron D4N-1A20R Datasheet preview
D4N-1A20R
Brand: Omron Pages: 16
Metrix SW6000 Installation Manual preview
SW6000
Brand: Metrix Pages: 12
LEGRAND HKRL20 Installation Manual preview
HKRL20
Brand: LEGRAND Pages: 30
OTS IES8242MPp9H-S-DR Quick Installation Manual preview
IES8242MPp9H-S-DR
Brand: OTS Pages: 3
GeoVision GV-POE2411-V2 Manual preview
GV-POE2411-V2
Brand: GeoVision Pages: 7
Harman AMX PR01-0808 User Manual preview
AMX PR01-0808
Brand: Harman Pages: 50
Tabs TBGW100-915 Reference Manual preview
TBGW100-915
Brand: Tabs Pages: 4
Black Box KV1044A-R2 Specifications preview
KV1044A-R2
Brand: Black Box Pages: 4
Minicom DX DX 432 Operating Manual preview
DX 432
Brand: Minicom DX Pages: 36
TP-Link LiteWave LS105G Installation Manual preview
LiteWave LS105G
Brand: TP-Link Pages: 3

Brands by name

Popular brands

Load more brands