manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

198

 

IP Interface Commands 

 

 

config ipif 

Purpose 

Used  to  configure  an  IP  interface  on  the 
switch. 

Syntax 

config ipif <ipif_name> {vlan 
<vlan_name>/ipaddress 
<network_address>/state 
[enabled/disabled]} 

Description 

This command is used to modify an existing 
IP interface on the switch. 

Parameters 

<ipif_name> 

−

  The  name  of  the  IP  interface 

to be configured on the switch.  

<vlan_name> 

−

  The  name  of  the  VLAN  that 

corresponds to the IP interface above. 

<network_address> 

−

  IP  address  and 

netmask  of  the  IP  interface  to  be  created.  
You  can  specify  the  address  and  mask 
information using the traditional format (for 
example,  10.1.2.3/255.0.0.0  or  in  CIDR 
format, 10.1.2.3/16). 

state  [enabled/disabled] 

−

  Allows  you  to 

enable or disable the IP interface. 

Restrictions 

Only  administrator-level  users  can  issue 
this command. 

 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Pathway connectivity solutions 1016 Manual preview
1016
Brand: Pathway connectivity solutions Pages: 2
Balluff IO-Link BNI LH1-303-S11-K091 Installation Manual preview
IO-Link BNI LH1-303-S11-K091
Brand: Balluff Pages: 12
D-Link DES-3224 - Switch User Manual preview
DES-3224 - Switch
Brand: D-Link Pages: 75
Network Technologies VEEMUX SM-nXm-15V-LC Installation And Operation Manual preview
VEEMUX SM-nXm-15V-LC
Brand: Network Technologies Pages: 46
XtendLan MATRIX1608A User Manual preview
MATRIX1608A
Brand: XtendLan Pages: 24
Ihse Draco tera compact 480 Series User Manual preview
Draco tera compact 480 Series
Brand: Ihse Pages: 244
3Com 3C16710 - OfficeConnect 8/TPM Hub User Manual preview
3C16710 - OfficeConnect 8/TPM Hub
Brand: 3Com Pages: 130
Eaton Cooper Power Systems LCR 6200 RFN Instructional Leaflet preview
Cooper Power Systems LCR 6200 RFN
Brand: Eaton Pages: 8
Free-Way Switch 3X3-08 Instructions Manual preview
3X3-08
Brand: Free-Way Switch Pages: 6
Net Generation NG-PGS164W User Manual preview
NG-PGS164W
Brand: Net Generation Pages: 38
FS S3200 Series Quick Start Manual preview
S3200 Series
Brand: FS Pages: 41
HIKVISION DS-PDEB-EG2-WE Manual preview
DS-PDEB-EG2-WE
Brand: HIKVISION Pages: 5
NETGEAR ProSAFE JGS516PE Installation Manual preview
ProSAFE JGS516PE
Brand: NETGEAR Pages: 2
Digitronic CamCon DC30 User Manual preview
CamCon DC30
Brand: Digitronic Pages: 24
NBK EORP-200 Instruction Manual preview
EORP-200
Brand: NBK Pages: 32
KYLAND Ruby3A Hardware Installation Manual preview
Ruby3A
Brand: KYLAND Pages: 34
TRENDnet TEG-S80Dg Brochure & Specs preview
TEG-S80Dg
Brand: TRENDnet Pages: 2
Allen-Bradley ferrogard gd2 Installation Instructions preview
ferrogard gd2
Brand: Allen-Bradley Pages: 4

Brands by name

Popular brands

Load more brands