manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

IGMP Snooping Commands 

249 

 

 

show igmp_snooping 

Purpose 

Used  to  show  the  current  status  of  IGMP 
snooping on the switch. 

Syntax 

show igmp_snooping {vlan <vlan_name>} 

Description 

This command will display the current IGMP 
snooping configuration on the switch. 

Parameters 

<vlan_name> 

−

  The  name  of  the  VLAN  for 

which  you  want  to  view  the  IGMP  snooping 
configuration. 

Restrictions 

none. 

 

Example Usage: 

To show igmp snooping: 

 

DES-3326SR:4#show igmp_snooping 
Command: show igmp_snooping 
 
 IGMP Snooping Global State      : Disabled 
 Multicast router Only                   : Disabled 
 VLAN  Name                                 : default 
 Query Interval                               : 125 
 Max Response Time                    : 10 
 Robustness Value                        : 2 
 Last Member Query Interval        : 1 
 Host Timeout                                : 260 
 Route Timeout                              : 260 
 Leave Timer                                  : 2 
 Querier State                                  : Disabled 
 Querier Router Behavior               : Non-Querier 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

D-Link xStack DGS-3427 User Manual preview
xStack DGS-3427
Brand: D-Link Pages: 246
Edimax GS-1016 Datasheet preview
GS-1016
Brand: Edimax Pages: 2
ORVIBO ZigBee Mini Hub Faq preview
ZigBee Mini Hub
Brand: ORVIBO Pages: 3
Vivotek AW-FGT-100C-120 Quick Installation Manual preview
AW-FGT-100C-120
Brand: Vivotek Pages: 2
G&D TradeSwitch2-USB Assembly, Installation And Operation Manual preview
TradeSwitch2-USB
Brand: G&D Pages: 88
Gefen EXT-DP-EDIDP User Manual preview
EXT-DP-EDIDP
Brand: Gefen Pages: 56
Raritan PC-Share Installation And Operation preview
PC-Share
Brand: Raritan Pages: 4
ALFAtron ALF- WUK3A Manual preview
ALF- WUK3A
Brand: ALFAtron Pages: 15
Unipoe PM5003GSN User Manual preview
PM5003GSN
Brand: Unipoe Pages: 9
Cabletron Systems ELS10-26TX User Manual preview
ELS10-26TX
Brand: Cabletron Systems Pages: 116
J-Tech Digital JTD-3003 User Manual preview
JTD-3003
Brand: J-Tech Digital Pages: 13
BERNSTEIN CSMS-M-R-H-KA Installation And Operating Instructions Manual preview
CSMS-M-R-H-KA
Brand: BERNSTEIN Pages: 38
serverLink SL-271-H Quick Installation Manual preview
SL-271-H
Brand: serverLink Pages: 2
IBM 8265 Nways ATM Switch Product Description preview
8265 Nways ATM Switch
Brand: IBM Pages: 100
JUKI 0040113520 Wiring Instructions preview
0040113520
Brand: JUKI Pages: 2
Net Optics Director xStream Pro Quick Install Manual preview
Director xStream Pro
Brand: Net Optics Pages: 2
Belden Thinklogical TLX640 Product Manual preview
Thinklogical TLX640
Brand: Belden Pages: 48
Panduit ATLONA AT-HDR-SW-51 Manual preview
ATLONA AT-HDR-SW-51
Brand: Panduit Pages: 58

Brands by name

Popular brands

Load more brands