manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

IGMP Commands 

237 

 

show igmp group 

Purpose 

Used  to  display  the  switch

’

s  IGMP  group 

table. 

Syntax 

show  igmp  group  {group  <group>}  {ipif 
<ipif_name>} 

Description 

This command will display the IGMP group 
configuration. 

Parameters 

group <group> 

−

 The multicast group ID. 

<ipif_name> 

−

 The name of the IP interface 

the IGMP group is part of. 

Restrictions 

none. 

Example Usage: 

To display IGMP group table: 

DES-3326SR:4#show igmp group 
Command: show igmp group 
 
Interface Name  Multicast Group  Last Reporter  Querier IP Address 
IP  Expire Time 
--------------------  -------------------  --------------------- ------------------------ ------
------------- 
System              224.0.0.2          10.42.73.111      10.48.74.122                     
260 
System              224.0.0.9              10.20.53.1      10.48.74.122                     
260 
System            224.0.1.24                10.18.1.3      10.48.74.122                     
259 
System            224.0.1.41            10.1.43.252      10.48.74.122                     
259 
System          224.0.1.149            10.20.63.11      10.48.74.122                    

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Aethra MTX200 Connection Manual preview
MTX200
Brand: Aethra Pages: 1
KCC KTD-600 Series Manual preview
KTD-600 Series
Brand: KCC Pages: 6
Icy Box IB-AC618 Manual preview
IB-AC618
Brand: Icy Box Pages: 6
Paugge ENT-MX20B16X16 User Manual preview
ENT-MX20B16X16
Brand: Paugge Pages: 20
Talkswitch CT.TS005.003902 User Manual preview
CT.TS005.003902
Brand: Talkswitch Pages: 309
Ametek SIL IntelliPoint RF S*R*L Series Installation And Operating Instructions Manual preview
SIL IntelliPoint RF S*R*L Series
Brand: Ametek Pages: 93
Cable Electronics HSW44C Plus Instruction Manual preview
HSW44C Plus
Brand: Cable Electronics Pages: 16
N-Tron 708TX User Manual & Installation Manual preview
708TX
Brand: N-Tron Pages: 157
ALFAtron ALF-MUH88E User Manual preview
ALF-MUH88E
Brand: ALFAtron Pages: 44
Black Box LGB2118A-R2 Startup Manual preview
LGB2118A-R2
Brand: Black Box Pages: 20
Linksys EG008W - Instant Gigabit Workgroup Switch User Manual preview
EG008W - Instant Gigabit Workgroup Switch
Brand: Linksys Pages: 27
Hama 5-Port Gigabit Switch 1000 Mbps User Manual preview
5-Port Gigabit Switch 1000 Mbps
Brand: Hama Pages: 2
AMERITRON RCS-12 Instruction Manual preview
RCS-12
Brand: AMERITRON Pages: 16
Honeywell Home 50027910-001 Installation Instructions preview
50027910-001
Brand: Honeywell Home Pages: 4
Efapel 40214 Instructions Manual preview
40214
Brand: Efapel Pages: 44
Primewire 302523/20191008SZ114 User Manual preview
302523/20191008SZ114
Brand: Primewire Pages: 12
EKOBUY ekb10075 User Manual preview
ekb10075
Brand: EKOBUY Pages: 8
Key Digital Champion SeriesKD-2x1CSK Operating Instructions Manual preview
Champion SeriesKD-2x1CSK
Brand: Key Digital Pages: 6

Brands by name

Popular brands

Load more brands