D-Link DES-3326SRM Page 91 Command Line Interface Reference Manual Download | Manualshive

Page: 91 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Network Management Commands

91

config mac_notification

number, and the highest port number of the
range  (also  separeted  by  a  colon)  are
specified. The beginning and end of the port
list  range  are  seperated  by  a  dash.    For
example,  1:3  would  specify  switch  number
1,  port  3.    2:4  specifies  switch  number  2,
port  4.    1:3-2:4  specifies  all  of  the  ports
between switch 1, port 3 and switch 2, port
4

−

in numerical order.

all

–

to configure all ports for MAC

notification.

interval <sec> - time in seconds between
notifications.

historysize <1 - 500> - maximum number
of entries listed in the history log used
for notification.

Restrictions

Only administrator-level users can issue
this command.

Example Usage:

To enable MAC address notification for unit 1 ports 6-9:

DES-3326SR:4#config mac_notification ports 1:6-1:9 enabled
Command: config mac_notification ports 1:6-1:9 enabled

Success.

DES-3326SR:4#

«
...
89
90
91
92
93
...
»

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Brand: OEM Pages: 1

ProConnect PS2KVM2

Brand: Linksys Pages: 17

TigerAccess SMC7824M/FSW

Brand: SMC Networks Pages: 2

Brand: Black Box Pages: 74

Genesis Digital HSM-04-02

Brand: Hall Research Technologies Pages: 28

Brand: N-Tron Pages: 157

Brand: ALFAtron Pages: 44

Brand: Black Box Pages: 20

AVS-OCT-4832-117

Brand: AMX Pages: 1

Brand: Hama Pages: 14

Brand: MicroNet Pages: 74

Brand: Grandbeing Pages: 27

Brand: Smart-M Pages: 2

Brand: Quark-Elec Pages: 10

Brand: N-Tron Pages: 17

Brand: IBM Pages: 60

menber's Series

Brand: Littelfuse Pages: 2

Brand: F&F Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands