manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

42

 

Basic Switch Commands 

 

 

reboot 

Purpose 

Used to restart the switch. 

Syntax 

reboot 

Description 

This command is used to restart the switch. 

Parameters 

none. 

Restrictions 

none. 

 

Example Usage: 

 

To restart the switch: 

 

DES-3326SR:4#reboot 
Command: reboot 

Are  you  sure  want  to  proceed  with  the  system 
reboot? (y/n) 

Please wait, the switch is rebooting... 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

UNICOM DynaGST/2402G GEP-33224T-1 Specifications preview
DynaGST/2402G GEP-33224T-1
Brand: UNICOM Pages: 1
UNICONTROL Electronic Cleveland Controls RSS-498-013 Manual preview
Cleveland Controls RSS-498-013
Brand: UNICONTROL Electronic Pages: 2
Eaton ATC-900 Manual preview
ATC-900
Brand: Eaton Pages: 40
GBC 34.0109.41 Quick Start Manual preview
34.0109.41
Brand: GBC Pages: 2
MuxLab HM44 User Manual preview
HM44
Brand: MuxLab Pages: 32
I-Tech NVCIP800 User Manual preview
NVCIP800
Brand: I-Tech Pages: 29
Moxa Technologies PT-G7509 Hardware Installation Manual preview
PT-G7509
Brand: Moxa Technologies Pages: 7
TRENDnet TE100-S24D Specifications preview
TE100-S24D
Brand: TRENDnet Pages: 2
Farallon Fast Starlet User Manual preview
Fast Starlet
Brand: Farallon Pages: 22
StarTech.com VS221HD20 Quick Start Manual preview
VS221HD20
Brand: StarTech.com Pages: 2
I-Tech NPXW117 User Manual preview
NPXW117
Brand: I-Tech Pages: 19
Linkskey LDV-DM702AUSK Quick Installation Manual preview
LDV-DM702AUSK
Brand: Linkskey Pages: 2
OTS ET2212PpH-S-DR Quick Installation Manual preview
ET2212PpH-S-DR
Brand: OTS Pages: 3
BENDIX SL-3-SL-4 STOP LIGHT SWITCH Manual preview
SL-3-SL-4 STOP LIGHT SWITCH
Brand: BENDIX Pages: 4
C&H Technologies M218 User Manual preview
M218
Brand: C&H Technologies Pages: 28
InvoTek BlueHub User Manual preview
BlueHub
Brand: InvoTek Pages: 4
Taiden HCS-4310M User Manual preview
HCS-4310M
Brand: Taiden Pages: 4
Gefen EXT-DVIK-MV-441 User Manual preview
EXT-DVIK-MV-441
Brand: Gefen Pages: 136

Brands by name

Popular brands

Load more brands