manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

116

 

Network Monitoring Commands 

 

create syslog host 

local4 

−

 Specifies that local use 4 messages 

will be sent to the remote host.  This 
corresponds to number 20 from the list 
above. 

local5 

−

 Specifies that local use 5 messages 

will be sent to the remote host.  This 
corresponds to number 21 from the list 
above. 

local6 

−

 Specifies that local use 6 messages 

will be sent to the remote host.  This 
corresponds to number 22 from the list 
above. 

local7 

−

 Specifies that local use 7 messages 

will be sent to the remote host.  This 
corresponds to number 23 from the list 
above. 

udp_port <int> 

−

 Specifies the UDP port 

number that the syslog protocol will use to 
send messages to the remote host. 

ipaddress <ipaddr> 

−

 Specifies the IP address of 

the remote host where syslog messages will be 
sent. 

state [enabled/disabled] 

−

 Allows the sending of 

syslog messages to the remote host, specified 
above, to be enabled and disabled. 

Restrictions 

Only administrator-level users can issue this 
command. 

Example Usage: 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

JDS Uniphase SB Series User Manual preview
SB Series
Brand: JDS Uniphase Pages: 40
Fantech DB10 Installation Instructions preview
DB10
Brand: Fantech Pages: 4
WAGO 852-111 Mounting, Installation And Handling preview
852-111
Brand: WAGO Pages: 39
LEGRAND WZ3RL10 Installation Instructions preview
WZ3RL10
Brand: LEGRAND Pages: 2
Maipu MyPower S2300-28TC-AC Installation Manual preview
MyPower S2300-28TC-AC
Brand: Maipu Pages: 31
ATEN CN8000 KVM on the NET Quick Start Manual preview
CN8000 KVM on the NET
Brand: ATEN Pages: 2
Penguin Edge RTM-ATCA-F140 Quick Start Manual preview
Edge RTM-ATCA-F140
Brand: Penguin Pages: 2
N-Tron 7014 Series Firmware Upgrade Procedure preview
7014 Series
Brand: N-Tron Pages: 5
LevelOne GSW-0509 Quick Installation Manual preview
GSW-0509
Brand: LevelOne Pages: 17
Magnetrol STI Echotel 919 Installation And Operating Manual preview
STI Echotel 919
Brand: Magnetrol Pages: 12
Hamlet XUSB370MS User Manual preview
XUSB370MS
Brand: Hamlet Pages: 2
Linkskey LKU -UA02 Quick Installation Manual preview
LKU -UA02
Brand: Linkskey Pages: 2
Pulsar SG108 Quick Start Manual preview
SG108
Brand: Pulsar Pages: 5
VigilLink VL-MX88-1 User Manual preview
VL-MX88-1
Brand: VigilLink Pages: 24
A-Neuvideo ANI-44VGA Instruction Manual preview
ANI-44VGA
Brand: A-Neuvideo Pages: 9
Whelen Engineering Company PCCS9LW Installation Manual preview
PCCS9LW
Brand: Whelen Engineering Company Pages: 5
KTI KGS-1620 Installation Manual preview
KGS-1620
Brand: KTI Pages: 25
ATEN CS1308 User Manual preview
CS1308
Brand: ATEN Pages: 68

Brands by name

Popular brands

Load more brands