manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

192

 

Link Aggregation Commands 

 

 

config link_aggregation algorithm 

Purpose 

Used to configure the link aggregation algorithm.  

Syntax 

config link_aggregation algorithm 
[mac_source/mac_destination/mac_source_de
st/ ip_source/ip_destination/ip_source_dest] 

Description 

This  command  configures  to  part  of  the  packet 
examined  by  the  switch  when  selecting  the 
egress  port  for  transmitting  load-sharing  data.  
This  feature  is  only  available  using  the  address-
based load-sharing algorithm. 

Parameters 

mac_source 

−

  Indicates  that  the  switch  should 

examine the MAC source address. 

mac_destination 

−

  Indicates  that  the  switch 

should examine the MAC destination address. 

mac_source_dest 

−

  Indicates  that  the  switch 

should examine the MAC source and destination 
addresses 

ip_source 

−

  Indicates  that  the  switch  should 

examine the IP source address. 

ip_destination 

−

 Indicates that the switch should 

examine the IP destination address. 

ip_source_dest 

−

 Indicates that the switch should 

examine  the  IP  source  address  and  the 
destination address. 

Restrictions  Only  administrator-level  users  can  issue  this 

command. 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

S&C 2000 series Instructions For Field Assembly And Installation preview
2000 series
Brand: S&C Pages: 26
S&C 2000 series Installation And Operation Manual preview
2000 series
Brand: S&C Pages: 37
S&C 2000 series Installation Manual preview
2000 series
Brand: S&C Pages: 28
FELA SWITCH CASAMBI Operation And Installation Manual preview
SWITCH CASAMBI
Brand: FELA Pages: 13
Balluff IO-Link BNI LH1-303-S11-K091 Installation Manual preview
IO-Link BNI LH1-303-S11-K091
Brand: Balluff Pages: 12
Qlogic SilverStorm 9000 Hardware Installation Manual preview
SilverStorm 9000
Brand: Qlogic Pages: 50
StarTech.com 8STSV211HDUA4K Quick Start Manual preview
8STSV211HDUA4K
Brand: StarTech.com Pages: 2
Hirschmann PAT TRS 05 / PATB3 Installation And Setup Manual preview
PAT TRS 05 / PATB3
Brand: Hirschmann Pages: 12
G&D DL-DVI-MUX2-NT SERIES Installation And Operation Manual preview
DL-DVI-MUX2-NT SERIES
Brand: G&D Pages: 76
NBase Communications NH2001M Installation And User Manual preview
NH2001M
Brand: NBase Communications Pages: 72
3Com Unified Gigabit Wireless PoE Switch 24... Quick Start Manual preview
Unified Gigabit Wireless PoE Switch 24...
Brand: 3Com Pages: 40
Fairchild FSDH321 Manual preview
FSDH321
Brand: Fairchild Pages: 20
WAGO 852-1411/000-001 Manual preview
852-1411/000-001
Brand: WAGO Pages: 40
Dahua PFS4226-24ET-240 User Manual preview
PFS4226-24ET-240
Brand: Dahua Pages: 3
Contec SH-9008AT-POE Reference Manual preview
SH-9008AT-POE
Brand: Contec Pages: 38
Sven HB-012 User Manual preview
HB-012
Brand: Sven Pages: 4
Penguin Computing Arctica 1600cs Installation Manual preview
Arctica 1600cs
Brand: Penguin Computing Pages: 71
ALFAtron SC61E Manual preview
SC61E
Brand: ALFAtron Pages: 23

Brands by name

Popular brands

Load more brands