manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

Arp Commands 

209 

 

 

create arpentry 

Purpose 

Used  to  make  a  static  entry  into  the  ARP 
table. 

Syntax 

create arpentry <ipaddr> <macaddr> 

Description 

This  command  is  used  to  enter  an  IP 
address  and  the  corresponding  MAC 
address into the switch

’

s ARP table. 

Parameters 

<ipaddr> 

−

  The  IP  address  of  the  end  node 

or station. 

<macaddr> 

−

 

The 

MAC 

address 

corresponding to the IP address above. 

Restrictions 

Only  administrator-level  users  can  issue 
this command. 

 

Example Usage: 

To create a static arp entry for the IP address 10.48.74.121 and 
MAC address 00:50:BA:00:07:36: 

 

DES-3326SR:4#create arpentry 10.48.74.121 00-50-BA-00-07-36 
Command: create arpentry 10.48.74.121 00-50-BA-00-07-36 
 
 Success. 
 
DES-3326SR:4# 

 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

S&C 2000 series Instructions For Field Assembly And Installation preview
2000 series
Brand: S&C Pages: 26
S&C 2000 series Installation And Operation Manual preview
2000 series
Brand: S&C Pages: 37
S&C 2000 series Installation Manual preview
2000 series
Brand: S&C Pages: 28
Talkswitch switch Start Manual preview
switch
Brand: Talkswitch Pages: 17
Cabletron Systems MicroMMAC-22E Installation Manual preview
MicroMMAC-22E
Brand: Cabletron Systems Pages: 83
hager WBMSLL Quick Start Manual preview
WBMSLL
Brand: hager Pages: 2
HIKVISION DS-3E0108P-E User Manual preview
DS-3E0108P-E
Brand: HIKVISION Pages: 25
Optex OAM-DUAL T Operation Manual preview
OAM-DUAL T
Brand: Optex Pages: 2
Hall Research Technologies KVMC-UH-8 User Manual preview
KVMC-UH-8
Brand: Hall Research Technologies Pages: 9
Flamingo SF500WD Quick Start Manual preview
SF500WD
Brand: Flamingo Pages: 2
Intel Ethernet Switch Boards Product Manual preview
Ethernet Switch Boards
Brand: Intel Pages: 52
LevelOne GTL-2690 Installation Manual preview
GTL-2690
Brand: LevelOne Pages: 76
National Instruments SwitchBlock Getting Started Manual preview
SwitchBlock
Brand: National Instruments Pages: 12
Comm-Tec MTX0804RA User Manual preview
MTX0804RA
Brand: Comm-Tec Pages: 10
Linkskey LKV-T02 Quick Installation Manual preview
LKV-T02
Brand: Linkskey Pages: 2
M-E CUVEO CT-W2 Manual preview
CUVEO CT-W2
Brand: M-E Pages: 36
Kramer VP-26 User Manual preview
VP-26
Brand: Kramer Pages: 46
Conrad RSLT2 Operating Instructions Manual preview
RSLT2
Brand: Conrad Pages: 8

Brands by name

Popular brands

Load more brands