manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

38

 

Basic Switch Commands 

 

disable telnet 

Purpose 

Used  to  disable  the  Telnet  protocol  on  the 
switch. 

Syntax 

disable telnet 

Description 

This command is used to disable the Telnet 
protocol on the switch. 

Parameters 

none. 

Restrictions 

Only  administrator-level  users  can  issue 
this command. 

 

Example Usage: 

To disable the Telnet protocol on the switch: 

 

DES-3326SR:4#disable telnet 
Command: disable telnet 
 
 Success. 
 
DES-3326SR:4# 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Omega Engineering 430 Instruction Sheet preview
430
Brand: Omega Engineering Pages: 3
E-Trailer E-Switch Product Manual preview
E-Switch
Brand: E-Trailer Pages: 8
H3C s5820x series Quick Start Manual preview
s5820x series
Brand: H3C Pages: 32
H3C S5830V2 series Mce Command Reference preview
S5830V2 series
Brand: H3C Pages: 22
H3C s5820x series Command Reference Manual preview
s5820x series
Brand: H3C Pages: 488
H3C S10500X Series Installation, Quick Start preview
S10500X Series
Brand: H3C Pages: 3
H3C S7500 Series Manual preview
S7500 Series
Brand: H3C Pages: 8
H3C S7500 Series Command Manual preview
S7500 Series
Brand: H3C Pages: 25
H3C S12500 Series Manual preview
S12500 Series
Brand: H3C Pages: 31
H3C S12500 Series Interface Configuration Manual preview
S12500 Series
Brand: H3C Pages: 23
H3C S12500 Series Software Upgrade preview
S12500 Series
Brand: H3C Pages: 24
H3C S12500 Series Installation Instructions Manual preview
S12500 Series
Brand: H3C Pages: 126
H3C S12500-X Configuration Manual preview
S12500-X
Brand: H3C Pages: 42
H3C S6300 Series Troubleshooting Manual preview
S6300 Series
Brand: H3C Pages: 32
H3C S7500 Series Installation Manual preview
S7500 Series
Brand: H3C Pages: 13
H3C S12500 Series Reference preview
S12500 Series
Brand: H3C Pages: 16
H3C S12500 Series Configuration Manual preview
S12500 Series
Brand: H3C Pages: 39
hager EMN005 User Instructions preview
EMN005
Brand: hager Pages: 2

Brands by name

Popular brands

Load more brands