D-Link DES-3326SRM Command Line Interface Reference Manual Download | Manualshive

Page: 125 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Spanning Tree Commands

125

config stp

Purpose

Used to setup STP and RSTP on the switch.

Syntax

config stp {maxage <value>/hellotime
<value>/forwarddelay <value>/priority
<value>/fbpdu [enabled/disabled]/
txholdcount <1-10>/ version[rstp/stp]}

Description

This command is used to setup the
Spanning Tree Protocol (STP) for the entire
switch.

Parameters

maxage <value>

−

The maximum amount of

time (in seconds) that the switch will wait to
receive a BPDU packet before reconfiguring
STP. The default is 20 seconds.

hellotime <value>

−

The time interval

between transmission of configuration
messages by the root device. The default is 2
seconds.

forwarddelay <value>

−

The maximum

amount of time (in seconds) that the root
device will wait before changing states. The
default is 15 seconds.

priority <value>

−

A numerical value

between 0 and 65535 that is used in
determining the root device, root port, and
designated port. The device with the highest
priority becomes the root device. The lower
the numerical value, the higher the priority.
The default is 32,768.

fbpdu [enabled/disabled]

−

Allows the

forwarding of STP BPDU packets from other

«
...
123
124
125
126
127
...
»

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Brand: Keithley Pages: 434

IPS7110-2GC-8POE

Brand: 3One data Pages: 3

Brand: N-Tron Pages: 5

Brand: LevelOne Pages: 17

Brand: Watchguard Pages: 26

Brand: CableTronix Pages: 4

Brand: Eaton Pages: 5

Brand: Intel Pages: 162

SICOM3432G Series

Brand: KYLAND Pages: 29

Brand: Icy Box Pages: 12

IPES/IES-5416T Series

Brand: Lantech Pages: 27

Brand: Witura Pages: 12

Brand: Rackmount Pages: 17

Brand: Linksys Pages: 22

Brand: IBM Pages: 2

Brand: Buffalo Pages: 2

Brand: SDMO Pages: 24

Brand: IBM Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands