background image

BS-GU2005

TM

Hardware Manual

Package Contents

The package contains the items shown below. If any items are missing,

please contact the dealer where you purchased this product.

The appearance of this product may vary from the illustration.

 Switch (main unit)................................................................................................. 1

Power connector

Connect the included power cable to this connector.

Indicators

LAN ports

These are ports for connecting 

1000BASE-T/100BASE-TX/10BASE-T devices.

Link/Act/Speed LED

On (green): 1000 Mbps linked.

On (amber): 100 or 10 Mbps linked.

Blinking (green or amber): Transmitting data.

Blinking once per second (green or amber): A loop is detected.

Power/Loop LED

On (green): Power is on.

Blinking once per second (red): A loop is detected.

 Power cable............................................................................................................. 1

 Rubber feet.............................................................................................................. 4

 Serial number stickers......................................................................................... 2

 Hardware manual (this document) ................................................................ 1

 Warranty................................................................................................................... 1

Only use the cables and accessories that are included in the package. Don't 
use other accessories or cables unless specifically instructed to in the 
documentation.

Installation

Precautions for Installation

• Do not install the device in an unstable location such as on an unsteady 

table or an inclined surface.

• Do not place another hub or object that generates heat on this unit.
• Please route all cables properly to prevent people from tripping over them.
• Ensure the air vents on the product are not blocked by other equipment or 

walls.

• Only use the power cable included with the product. Using other power 

cables may result in damage or fire.

Floor or Shelf Mounting

Attach the supplied rubber feet to the bottom corners of the unit before

use.

Mounting to a Metal Surface

To mount to a metal surface, such as the side of a steel desk, use the
"BS-MGK-A Magnet Kit" (sold separately). Attach the supplied rubber feet to 

the bottom corners of the unit before using the magnet kit.

Caution: Do not put floppy discs, magnetic cards, or other magnetic storage 

media near magnets. Doing so may delete or corrupt data.

Note: If the switch is secured by the magnet kit alone, it should be no more 

than 75 cm (29.5 in) from the floor.

Mounting to a Wall

To mount the unit directly to the wall, use 2 screws (not included) with the 

dimensions shown below. Install the screws 78 mm (3.07 in) apart and slide 

the mounting holes on the base of the switch over them.

2

3

φ6

Loop Detection

This unit can detect network loops that can cause interference in the network.

Turning Loop Detection On and Off

1. Use the switch on the front of the switch to turn loop detection on or off.

2. Disconnect power cable and reconnect it.

When a Loop Is Detected

Reconnect your Ethernet cabling, making sure that there are no redundant 

connections.

Loop Detection

Off: Loops are not detected.

On: If a network loop is detected, the power/loop, and link/act/speed LEDs for 

the detected port blink once per second.

Loop detection 

switch

This switches loop 

detection on and off.

What Is a Loop?

If both ends of an Ethernet cable are connected to the same hub, or when 

multiple connections exist between two hubs, data may be sent in a loop 

around the network, wasting network capacity and never getting to its 

destination. This continuously circulating data may interfere with other 

network communication.

Notes:

- While loop detection is enabled, this switch will send a loop detection packet 

through the network every two seconds. If these packets disrupt your network in 

any way, disable loop detection.

- Loop detection cannot detect all types of loops.

35020641-01

Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per 

Buffalo BS-GU2005

o cerca il tuo prodotto tra le 

migliori offerte di Switch

Reviews: