manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

Share
Download
D-Link DES-3326SRM Command Line Interface Reference Manual Download Page 181

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

VLAN Commands 

181 

 

 

enable gvrp 

Purpose 

Used to enable GVRP on the switch. 

Syntax 

enable gvrp 

Description 

This command, along with disable gvrp 
below, is used to enable and disable GVRP 
on the switch 

−

 without changing the GVRP 

configuration on the switch. 

Parameters 

None. 

Restrictions 

Only administrator-level users can issue 
this command. 

 

Example Usage: 

To enable the generic VLAN Registration Protocol (GVRP): 

 

DES-3326SR:4#enable gvrp 
Command: enable gvrp 
 
 Success. 
 
DES-3326SR:4#

 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands