manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

Basic Switch Commands 

39 

 

 

enable web 

Purpose 

Used to enable the HTTP-based 
management software on the switch. 

Syntax 

enable web <tcp_port_number> 

Description 

This command is used to enable the Web-
based management software on the switch.  
The user can specify the TCP port number 
the switch will use to listen for Telnet 
requests. 

Parameters 

<tcp_port_number> 

−

 The TCP port number.  

TCP ports are numbered between 1 and 
65535. The 

“

well-known

”

 port for the Web-

based management software is 80. 

Restrictions 

Only administrator-level users can issue 
this command. 

 

Example Usage:

 

To enable HTTP and configure port number: 

 

DES-3326SR:4#enable web 80 
Command: enable web 80 
 
 Success. 
 
DES-3326SR:4# 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Perel EMS113 User Manual preview
EMS113
Brand: Perel Pages: 4
netvox ZigBee Z815B User Manual preview
ZigBee Z815B
Brand: netvox Pages: 14
TRENDnet TE100-S5 Lühike Paigaldusjuhend preview
TE100-S5
Brand: TRENDnet Pages: 11
Sams RSS-10v User Manual For Use And Maintenance preview
RSS-10v
Brand: Sams Pages: 14
Comtrend Corporation ES-7211PoE User Manual preview
ES-7211PoE
Brand: Comtrend Corporation Pages: 2
Accton Technology ES4626 Management Manual preview
ES4626
Brand: Accton Technology Pages: 523
Gefen ToolBox GTB-MHDMI1.3-441 User Manual preview
ToolBox GTB-MHDMI1.3-441
Brand: Gefen Pages: 25
PRO SIGNAL PSG3061 Quick Start Manual preview
PSG3061
Brand: PRO SIGNAL Pages: 4
Scion SC03.4101 Operation Manual preview
SC03.4101
Brand: Scion Pages: 8
Uniclass AI-CP02A Quick Installation Manual preview
AI-CP02A
Brand: Uniclass Pages: 2
H3C S3100-16T P-EI-W Quick Start Manual preview
S3100-16T P-EI-W
Brand: H3C Pages: 60
Dataprobe iBootBar iBB-DC8 Installation And Operations preview
iBootBar iBB-DC8
Brand: Dataprobe Pages: 36
Lindy 32320 User Manual preview
32320
Brand: Lindy Pages: 12
Kensence S-Mix-Pro 18*18 Operation Manual preview
S-Mix-Pro 18*18
Brand: Kensence Pages: 24
Omnitron Systems Technology iConverter GX/X User Manual preview
iConverter GX/X
Brand: Omnitron Systems Technology Pages: 2
TRENDnet TI-G102 Quick Installation Manual preview
TI-G102
Brand: TRENDnet Pages: 2
Triax TMS 5XX SE AQ-EU Series User Manual preview
TMS 5XX SE AQ-EU Series
Brand: Triax Pages: 6
Mellanox Technologies Grid Director 4700 Installation Manual preview
Grid Director 4700
Brand: Mellanox Technologies Pages: 88

Brands by name

Popular brands

Load more brands