D-Link DES-3326SRM Page 245 Command Line Interface Reference Manual Download | Manualshive

Page: 245 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

IGMP Snooping Commands

245

Example Usage:

To configure the igmp snooping:

DES-3326SR:4#config igmp_snooping querier default
query_interval 125 state enabled

Command: config igmp_snooping querier default query_interval
125 state enabled

Success.

DES-3326SR:4#

config router_ports

Purpose

Used to configure ports as router ports.

Syntax

config router_ports <vlan_name>
[add/delete] <portlist>

Description

This  command  allows  you  to  designate  a
range  of  ports  as  being  connected  to
multicast-enabled  routers.    This  will  ensure
that  all  packets  with  such  a  router  as  its
destination  will  reach  the  multicast-enabled
router

−

regardless of protocol, etc.

Parameters

<vlan_name>

−

The name of the VLAN on

which the router port resides.

<portlist>

−

specifies a range of ports to be

configured. Ports are specified by entering
the lowest port number in a group, and then

«
...
243
244
245
246
247
...
»

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Brand: D-Link Pages: 2

Brand: Gavita Pages: 12

S5800-EI Series

Brand: H3C Pages: 61

Brand: Hanwell Pages: 109

Brand: Olympia Pages: 6

tekmarNet4 User Switch 480

Brand: Tekmar Pages: 8

Brand: NTI Pages: 15

Brand: Comtrend Corporation Pages: 2

NEXT-POE4210L2S-TP

Brand: Synology Pages: 15

Brand: Key Digital Pages: 31

Brand: Farallon Pages: 22

Brand: StarTech.com Pages: 2

Brand: G&D Pages: 80

Brand: Icy Box Pages: 12

Brand: Penguin Computing Pages: 71

Moeller IZM Series

Brand: Eaton Pages: 4

Brand: Pakedge Device & Software Pages: 8

Brand: Black Box Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands