D-Link DES-3326SRM Page 9 Command Line Interface Reference Manual Download | Manualshive

Page: 9 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Introduction

9

1

I

NTRODUCTION

The switch can be managed through the switch

’

s serial port,

Telnet, or the Web-based management agent. The Command Line
Interface (CLI) can be used to configure and manage the switch
via the serial port or Telnet interfaces.

This  manual  provides  a  reference  for  all  of  the  commands
contained  in  the  CLI.  Configuration  and  management  of  the
switch via  the  Web-based  management  agent  is  discussed  in  the
User

’

s Guide.

Accessing the Switch via the Serial Port

The switch

’

s serial port

’

s default settings are as follows:

•

9600 baud

•

no parity

•

8 data bits

•

1 stop bit

A computer running a terminal emulation program capable of
emulating a VT-100/ANSI terminal and a serial port configured as
above is then connected to the switch

’

s serial port via an RS-232

DB-9 cable.

You will initially encounter a blank screen; hit Enter twice and
the following screen will appear:

«
...
7
8
9
10
11
...
»

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Brand: Eaton Pages: 4

Brand: Ultra Pages: 20

Brand: BERNSTEIN Pages: 3

Matrix DFE-Gold 4G4202-60

Brand: Enterasys Pages: 78

Brand: ZENEC Pages: 16

Brand: AVLT-Power Pages: 12

Brand: AdLuminis Pages: 8

ProConnect PS2KVM2

Brand: Linksys Pages: 17

Brand: Atlantis Land Pages: 3

Brand: Kramer Pages: 2

Brand: Comm-Tec Pages: 48

Brand: Lightwave Pages: 53

Brand: ATEN Pages: 2

Brand: Pulse-Eight Pages: 9

Brand: BluStream Pages: 4

Hi-Speed USB 4-Port Bay Hub

Brand: SIIG Pages: 8

Brand: H3C Pages: 70

ISCOM2600G (A) Series

Brand: Raisecom Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands