manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

OSPF Configuration Commands 

333 

 

 

show ospf all 

Purpose 

Used to display the current OSPF settings of 
all the OSPF interfaces on the switch. 

Syntax 

show ospf all 

Description 

This command will display the current OSPF 
settings  for  all  OSPF  interfaces  on  the 
switch. 

Parameters 

none. 

Restrictions 

none. 

Usage Example 

 

To display the current OSPF settings: 

To  display  the  current  OSPF  interface  settings,  for  all  OSPF 
interfaces on the switch: 

DES-3326SR:4#show ospf all 
Command: show ospf all 
 
Interface Name:  System                    IP Address:  10.42.73.10/8 (Link 

Up) 

Network Medium Type: BROADCAST    Metric:  1 
Area ID:  0.0.0.0                                   Administrative State:  Enabled 
Priority:  1                                            DR State:  DR 
DR Address:  10.42.73.10                   Backup DR Address:  None 
Hello Interval:  10                                Dead Interval:  40 
Transmit Delay:  1                               Retransmit Time:  5 
Authentication:  None 
 
Interface Name:  ipif2                         IP Address:  123.234.12.34/24 

((Link Up) 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

3Com 4007 Release Note preview
4007
Brand: 3Com Pages: 128
3Com 4005 Datasheet preview
4005
Brand: 3Com Pages: 2
3Com 4200G 12-Port Configuration Manual preview
4200G 12-Port
Brand: 3Com Pages: 422
3Com 3CR16708-91 - OfficeConnect Managed Switch 9 Datasheet preview
3CR16708-91 - OfficeConnect Managed Switch 9
Brand: 3Com Pages: 4
3Com 3CR13501-73 Release Note preview
3CR13501-73
Brand: 3Com Pages: 5
3Com 3CR13500 Software Install Manual preview
3CR13500
Brand: 3Com Pages: 30
3Com 5500G SERIES Getting Started Manual preview
5500G SERIES
Brand: 3Com Pages: 36
3Com 3CNJ220-CRM Datasheet preview
3CNJ220-CRM
Brand: 3Com Pages: 4
3Com Baseline 2226-PWR Plus User Manual preview
Baseline 2226-PWR Plus
Brand: 3Com Pages: 77
3Com 3CRWX120695A Reference Manual preview
3CRWX120695A
Brand: 3Com Pages: 570
3Com OfficeConnect WX1200 Release Note preview
OfficeConnect WX1200
Brand: 3Com Pages: 28
3Com Baseline 2226-PWR Plus Datasheet preview
Baseline 2226-PWR Plus
Brand: 3Com Pages: 4
3Com CoreBuilder 6000 Supplementary Manual preview
CoreBuilder 6000
Brand: 3Com Pages: 31
i3 International S244 Quick Start Manual preview
S244
Brand: i3 International Pages: 2
Delta EXPERT-POE-54G User Manual preview
EXPERT-POE-54G
Brand: Delta Pages: 4
QCT QuantaMesh T1048-LB9 Installation Manual preview
QuantaMesh T1048-LB9
Brand: QCT Pages: 42
Cross Technologies 1582-225L2 Instruction Manual preview
1582-225L2
Brand: Cross Technologies Pages: 20
SMC Networks PF2A7 Series Operation Manual preview
PF2A7 Series
Brand: SMC Networks Pages: 43

Brands by name

Popular brands

Load more brands