D-Link DES-3326SRM Command Line Interface Reference Manual Download Page 47 | Manualshive

Page: 47 / 354

D-Link DES-3326SRM Command Line Interface Reference Manual Download Page 47

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Switch Port Commands

47

config ports

Purpose

Used to configure the switch

’

s Ethernet port

settings.

Syntax

config ports [<portlist/all>]
{speed[auto/10_half/10_full/100_half/100_hal
f/1000_full] learning [enabled/disabled] state
[enabled/disabled]}

Description

This command allows for the configuration of the
switch

’

s Ethernet ports. Only the ports listed in

the <portlist> will be affected.

Parameters

all

−

Displays all ports on the switch.

<portlist>

−

Specifies a range of ports to be

configured. The port list is specified by listing the
beginning port number and the highest port
number of the range. The beginning and end of
the port list range are separated by a dash. For
example, 3 would specify port 3. 4 specifies port
4. 3-4 specifies all of the ports between port 3
and port 4

−

in numerical order.

auto

−

Enables auto-negotiation for the specified

range of ports.

[10/100/1000]

−

Configures the speed in Mbps

for the specified range of ports. Gigabit ports are
statically set to 1000 and cannot be set to slower
speeds.

[half/full]

−

Configures the specified range of

ports as either full- or half-duplex.

learning [enabled/disabled]

−

Enables or disables

«
...
45
46
47
48
49
...
»

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands