manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

306

 

OSPF Configuration Commands 

 

 

disable ospf 

Purpose 

Used to disable OSPF on the switch. 

Syntax 

disable ospf 

Description 

This  command,  in  combination  with  the 
enable  ospf  command  above,  is  used  to 
enable and disable OSPF on the switch. 

Parameters 

none. 

Restrictions 

Only  administrator-level  users  can  issue 
this command. 

 

Usage Example 

 

To disable OSPF on the switch: 

DES-3326SR:4#disable ospf 
Command: disable ospf 
 
DES-3326SR:4#

 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

IDK MSD-804FD Series Command Manual preview
MSD-804FD Series
Brand: IDK Pages: 133
IDK MSD-72 Series User Manual preview
MSD-72 Series
Brand: IDK Pages: 150
IDK MSD-501 Command Reference Manual preview
MSD-501
Brand: IDK Pages: 101
IDK MSD-402 Command Reference Manual preview
MSD-402
Brand: IDK Pages: 85
IDK IMP-400UHD Command Reference Manual preview
IMP-400UHD
Brand: IDK Pages: 40
IDK FDX-32 User Manual preview
FDX-32
Brand: IDK Pages: 97
IDK FDX-S Series User Manual preview
FDX-S Series
Brand: IDK Pages: 117
IDK FDX-16 User Manual preview
FDX-16
Brand: IDK Pages: 77
Magnetrol B75 Installation And Operating Manual preview
B75
Brand: Magnetrol Pages: 28
3Com 4210G Series Configuration Manual preview
4210G Series
Brand: 3Com Pages: 1133
Vivotek AW-FGT-100C-120 Quick Installation Manual preview
AW-FGT-100C-120
Brand: Vivotek Pages: 2
H3C S5130S-EI series Hardware Information preview
S5130S-EI series
Brand: H3C Pages: 67
LEGRAND HKRL20 Installation Manual preview
HKRL20
Brand: LEGRAND Pages: 30
PABX 208AC Instruction Manual preview
208AC
Brand: PABX Pages: 46
Lantech IES-5216DF User Manual preview
IES-5216DF
Brand: Lantech Pages: 30
LEGRAND Plexo Instructions Manual preview
Plexo
Brand: LEGRAND Pages: 140
Raritan PC-Share Installation And Operation preview
PC-Share
Brand: Raritan Pages: 4
SLV 470819 Quick Installation Manual preview
470819
Brand: SLV Pages: 22

Brands by name

Popular brands

Load more brands