manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

Command Syntax 

19 

 

3 

C

OMMAND 

S

YNTAX

 

The following symbols are used to describe how command entries 
are made and values and arguments are specified in this manual. 
The  online  help  contained  in  the  CLI  and  available  through  the 
console interface uses the same syntax. 

 

<angle brackets> 

Purpose 

Encloses a variable or value that must be 
specified. 

Syntax 

create ipif <ipif_name> vlan <vlan_name> 
ipaddress <network_address> 

Description 

In the above syntax example, you must 
supply an IP interface name in the 
<ipif_name> space, a VLAN name in the 
<vlan_name> space, and the network 
address in the <network_address> space.  
Do not type the angle brackets. 

Example 
Command 

create ipif Engineering vlan Design 
ipaddress 10.24.22.5/255.0.0.0 

 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

3Com 3C17539 Datasheet preview
3C17539
Brand: 3Com Pages: 12
3Com S7906E - Switch Datasheet preview
S7906E - Switch
Brand: 3Com Pages: 8
Techroutes S3756 Hardware Installation Manual preview
S3756
Brand: Techroutes Pages: 22
Waters Network Systems ES1008-MSC Operating Manual preview
ES1008-MSC
Brand: Waters Network Systems Pages: 16
REV Ritter RF102R Assembly And Operating Instructions Manual preview
RF102R
Brand: REV Ritter Pages: 15
GBC 34.0109.41 Quick Start Manual preview
34.0109.41
Brand: GBC Pages: 2
Cabletron Systems 9F426-03 Appendix preview
9F426-03
Brand: Cabletron Systems Pages: 14
Dahua PFS4226-24ET-240 User Manual preview
PFS4226-24ET-240
Brand: Dahua Pages: 3
KYLAND SICOM3432G Series Hardware Installation Manual preview
SICOM3432G Series
Brand: KYLAND Pages: 29
Zektor HD800-V2 User Manual preview
HD800-V2
Brand: Zektor Pages: 41
Raritan SwitchMan USB-Combo SW4 Quick Installation And Setup Manual preview
SwitchMan USB-Combo SW4
Brand: Raritan Pages: 2
Kathrein EXE 1512 Manual preview
EXE 1512
Brand: Kathrein Pages: 41
Zigen ZIG-SW42 User Manual preview
ZIG-SW42
Brand: Zigen Pages: 18
Lucent Technologies 5ESS-2000 Operations And Maintenance Procedures preview
5ESS-2000
Brand: Lucent Technologies Pages: 1421
Eaton TRIPP LITE U360-004-IND Owner'S Manual preview
TRIPP LITE U360-004-IND
Brand: Eaton Pages: 56
Eaton TRIPP LITE U460-003-3AG Owner'S Manual preview
TRIPP LITE U460-003-3AG
Brand: Eaton Pages: 32
HP J8164A Manual Supplement preview
J8164A
Brand: HP Pages: 22
HP J4111A Schematics Manual preview
J4111A
Brand: HP Pages: 1

Brands by name

Popular brands

Load more brands