D-Link DES-3326SRM Page 282 Command Line Interface Reference Manual Download | Manualshive

Page: 282 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

282

DVMRP Commands

config dvmrp

Purpose

Used to configure DVMRP on the switch.

Syntax

config dvmrp [ipif <ipif_name>/all]
{metric <value>/probe
<second>/neighbor_timeout
<second>/state [enabled/disabled]

Description

This command is used to configure DVMRP
on the switch.

Parameters

<ipif_name>

−

The name of the IP interface

for which DVMRP is to be configured.
all

−

Specifies that DVMRP is to be

configured for all IP interfaces on the switch.
metric <value>

−

Allows the assignment of a

DVMRP route cost to the above IP interface.
A  DVMRP  route  cost  is  a  relative  number
that  represents  the  real  cost  of  using  this
route  in  the  construction  of  a  multicast
delivery tree.  It is similar to, but not defined
as, the hope count in RIP. The default is 1.
probe  <second>

−

DVMRP defined an

extension  to  IGMP  that  allows  routers  to
query  other  routers  to  determine  if  a
multicast group is present on a given router
subnetwork  or  not.    This  is  referred  to  as  a

‘

probe

’

. The default value is 10 seconds.

neighbor_timeout <second>

−

The time

period  for  which  DVMRP  will  hold  Neighbor
Router  reports  before  issuing  poison  route
messages. The default value is 35 seconds.
state  [enabled/disabled]

−

Allows DVMRP to

be enabled or disabled.

Restrictions

Only administrator-level users can issue
this command.

«
...
280
281
282
283
284
...
»

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Brand: ABLE Pages: 5

Brand: H3C Pages: 22

S5500-EI series

Brand: H3C Pages: 2

Brand: Qlogic Pages: 4

LambdaUnite MSS

Brand: Lucent Technologies Pages: 388

VEEMUX SM-nXm-15V-LC

Brand: Network Technologies Pages: 46

Brand: GBC Pages: 2

Brand: N-Tron Pages: 20

Brand: Velleman Pages: 5

Brand: Eaton Pages: 120

SET-2000 Oil/Sludge

Brand: Labkotec Pages: 15

SANbox 5000 Series

Brand: Qlogic Pages: 2

Brand: Clas Ohlson Pages: 4

Brand: ddtop Pages: 10

Brand: ELPRO Pages: 8

Brand: Quartz Pages: 43

Brand: LEGRAND Pages: 140

DOMINION KX II DKX2-0E-E

Brand: Raritan Pages: 257

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands