manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

DNS Relay Commands 

267 

 

 

enable dnsr cache 

Purpose 

Used to enable the DNS relay cache. 

Syntax 

enable dnsr cache 

Description 

This command is used, in combination with 
the  disable  dnsr  cache  command  below,  to 
enable and disable the DNS relay cache. 

Parameters 

none. 

Restrictions 

Only  administrator-level  users  can  issue 
this command. 

 

Example Usage: 

To enable cache lookup for DNS relay. 

 

DES-3326SR:4#enable dnsr cache 
Command: enable dnsr cache 
 

Success. 

 
DES-3326SR:4#

 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

D-Link DXS-5000-54S Quick Installation Manual preview
DXS-5000-54S
Brand: D-Link Pages: 17
SMC Networks PF2MC7 Series Operation Manual preview
PF2MC7 Series
Brand: SMC Networks Pages: 102
SMART Hub VE220 Installation And User Manual preview
Hub VE220
Brand: SMART Pages: 46
Cabletron Systems 2E43-51R Supplemental Manual preview
2E43-51R
Brand: Cabletron Systems Pages: 120
E-LINK LNK-IMC208P-SFP Quick Start Manual preview
LNK-IMC208P-SFP
Brand: E-LINK Pages: 6
Xunison Hub D60 5G Quick Start Manual preview
Hub D60 5G
Brand: Xunison Pages: 14
Accton Technology ES4626 Management Manual preview
ES4626
Brand: Accton Technology Pages: 523
VADA VFB-MSU20 Quick Start Manual preview
VFB-MSU20
Brand: VADA Pages: 4
APG FT-100 Series Operator'S Manual preview
FT-100 Series
Brand: APG Pages: 7
Rocstor Y10A251-B1 User Manual preview
Y10A251-B1
Brand: Rocstor Pages: 2
KTI KCB-121 User Manual preview
KCB-121
Brand: KTI Pages: 16
Zamel RWS-311D/Z Manual preview
RWS-311D/Z
Brand: Zamel Pages: 4
Black Box KVS4-1002D User Manual preview
KVS4-1002D
Brand: Black Box Pages: 15
lifeSMART BLEND Smart LS055 Quick Start Manual preview
BLEND Smart LS055
Brand: lifeSMART Pages: 13
TESmart CKS0301AIU User Manual preview
CKS0301AIU
Brand: TESmart Pages: 34
ATEN CS-128A User Manual preview
CS-128A
Brand: ATEN Pages: 30
Bang & Olufsen BeoSound Moment User Manual preview
BeoSound Moment
Brand: Bang & Olufsen Pages: 11
Wise P941 Instruction Manual preview
P941
Brand: Wise Pages: 8

Brands by name

Popular brands

Load more brands